| draft-ietf-sigtran-m3ua-08Description: Request For CommentsYou can download source copies of the file as follows:
Listed below is the contents of file draft-ietf-sigtran-m3ua-08.txt. Network Working Group Greg Sidebottom INTERNET-DRAFT Guy Mousseau Nortel Networks Lyndon Ong Ciena Ian Rytina Ericsson Hanns Juergen Schwarzbauer Siemens Klaus Gradischnig NeuStar Ken Morneault Cisco Mallesh Kalla Telcordia Normand Glaude Performance Technologies Brian Bidulock OpenSS7 Expires in six months Jul 2001 SS7 MTP3-User Adaptation Layer (M3UA) <draft-ietf-sigtran-m3ua-08.txt> Status of This Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as 'work in progress.' The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. To learn the current status of any Internet-Draft, please check the '1id-abstracts.txt' listing contained in the Internet- Drafts Shadow Directories on ftp.is.co.za (Africa), nic.nordu.net (Europe), munnari.oz.au (Pacific Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast). Abstract This Internet Draft defines a protocol for supporting the transport of any SS7 MTP3-User signalling (e.g., ISUP and SCCP messages) over IP using the services of the Stream Control Transmission Protocol. Also, provision is made for protocol elements that enable a seamless Sidebottom et al [Page 1] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 operation of the MTP3-User peers in the SS7 and IP domains. This protocol would be used between a Signalling Gateway (SG) and a Media Gateway Controller (MGC) or IP-resident Database. It is assumed that the SG receives SS7 signalling over a standard SS7 interface using the SS7 Message Transfer Part (MTP) to provide transport. Sidebottom et al [Page 2] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 TABLE OF CONTENTS 1. Introduction.......................................................4 1.1 Scope.........................................................4 1.2 Terminology...................................................4 1.3 M3UA Overview.................................................6 1.4 Functional Areas.............................................12 1.5 Sample Configurations........................................21 1.6 Definition of M3UA Boundaries................................24 2. Conventions.......................................................28 3. M3UA Protocol Elements............................................28 3.1 Common Message Header........................................28 3.2 Variable-Length Parameter....................................31 3.3 Transfer Messages............................................32 3.4 SS7 Signalling Network management (SSNM) Messages............35 3.5 ASP State Maintenance (ASPM) Messages........................43 3.6 Routing Key Management (RKM) Messages........................46 3.7 ASP Traffic Maintenance (ASPTM) Messages.....................55 3.8 Management(MGMT) Messages....................................60 4. Procedures........................................................64 4.1 Procedures to Support the M3UA-User and Layer Management Layers.......................................................64 4.2 Procedures to Support the Management of SCTP Associations with M3UA Peers..............................................67 4.3 Procedures to support the Unavailability or Congestion Status of SS7 Destinations...................................81 4.4 MTP3 Restart.................................................83 5. Examples of M3UA Procedures.......................................84 5.1 Establishment of Association and Traffic Between SGs and ASPs.........................................84 5.2 ASP traffic Fail-over Examples...............................89 5.3 Normal Withdrawal of an ASP from an Application Server and Tear-down of an Association..............................90 5.4.M3UA/MTP3-User Boundary Examples.............................91 6. Security..........................................................95 6.1 Introduction.................................................95 6.2 Threats......................................................95 6.3 Protecting Confidentiality...................................95 7. IANA Considerations...............................................96 7.1 SCTP Payload Protocol Identifier.............................96 7.2 M3UA Protocol Extensions.....................................96 8. Acknowledgements..................................................97 9. References........................................................97 10. Bibliography....................................................99 11. Author's Addresses..............................................99 Sidebottom et al [Page 3] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 1. Introduction 1.1 Scope There is a need for Switched Circuit Network (SCN) signalling protocol delivery from an SS7 Signalling Gateway (SG) to a Media Gateway Controller (MGC) or IP-resident Database as described in the Framework Architecture for Signalling Transport [1]. The delivery mechanism SHOULD meet the following criteria: * Support for the transfer of all SS7 MTP3-User Part messages (e.g., ISUP, SCCP, TUP, etc.) * Support for the seamless operation of MTP3-User protocol peers * Support for the management of SCTP transport associations and traffic between an SG and one or more MGCs or IP-resident Databases * Support for MGC or IP-resident Database process fail-over and load- sharing * Support for the asynchronous reporting of status changes to management In simplistic transport terms, the SG will terminate SS7 MTP2 and MTP3 protocol layers and deliver ISUP, SCCP and/or any other MTP3-User protocol messages, as well as certain MTP network management events, over SCTP transport associations to MTP3-User peers in MGCs or IP- resident Databases. 1.2 Terminology Application Server (AS) - A logical entity serving a specific Routing Key. An example of an Application Server is a virtual switch element handling all call processing for a unique range of PSTN trunks, identified by an SS7 SIO/DPC/OPC/CIC_range. Another example is a virtual database element, handling all HLR transactions for a particular SS7 DPC/OPC/SCCP_SSN combination. The AS contains a set of one or more unique Application Server Processes, of which one or more is normally actively processing traffic. Note that there is a 1:1 relationship between an AS and a Routing Key. Application Server Process (ASP) - A process instance of an Application Server. An Application Server Process serves as an active or back-up process of an Application Server (e.g., part of a distributed virtual switch or database). Examples of ASPs are processes (or process instances) of MGCs, IP SCPs or IP HLRs. An ASP contains an SCTP end- point and may be configured to process signalling traffic within more than one Application Server. Sidebottom et al [Page 4] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Association - An association refers to an SCTP association. The association provides the transport for the delivery of MTP3-User protocol data units and M3UA adaptation layer peer messages. IP Server Process (IPSP) - A process instance of an IP-based application. An IPSP is essentially the same as an ASP, except that it uses M3UA in a point-to-point fashion. Conceptually, an IPSP does not use the services of a Signalling Gateway. Signalling Gateway Process (SGP) - A process instance of a Signalling Gateway. It serves as an active, back-up, load-sharing or broadcast process of a Signalling Gateway. Signalling Gateway - An SG is a signaling agent that receives/sends SCN native signaling at the edge of the IP network [1]. An SG appears to the SS7 network as an SS7 Signalling Point. An SG contains a set of one or more unique Signalling Gateway Processes, of which one or more is normally actively processing traffic. Where an SG contains more than one SGP, the SG is a logical entity and the contained SGPs might typically be coordinated into a single management view to the SS7 network and to the supported Application Servers. Signalling Process - A process instance that uses M3UA to communicate with other signalling processes. An ASP, an SGP and an IPSP are all signalling processes. Routing Key: A Routing Key describes a set of SS7 parameters and parameter values that uniquely define the range of signalling traffic to be handled by a particular Application Server. Parameters within the Routing Key cannot extend across more than a single Signalling Point Management Cluster. Routing Context - A value that uniquely identifies a Routing Key. Routing Context values are either configured using a configuration management interface, or by using the routing key management procedures defined in this document. Fail-over - The capability to re-route signalling traffic as required to an alternate Application Server Process, or group of ASPs, within an Application Server in the event of failure or unavailability of a currently used Application Server Process. Fail-over also applies upon the return to service of a previously unavailable Application Server Process. Signalling Point Management Cluster (SPMC) - The complete set of Application Servers represented to the SS7 network under a single MTP entity (Signalling Point). SPMCs are used to aggregate the availability, congestion, and user part status of an MTP entity (Signalling Point) that is distributed in the IP domain, for the purpose of supporting MTP3 management procedures towards the SS7 network. In some Sidebottom et al [Page 5] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 cases, the SG itself may also be a member of the SPMC. In this case, the SG availability/congestion/User_Part status should also be taken into account when considering any supporting MTP3 management actions. MTP - The Message Transfer Part of the SS7 protocol. MTP3 - MTP Level 3, the signalling network layer of SS7 MTP3-User - Any protocol normally using the services of the SS7 MTP3 (e.g., ISUP, SCCP, TUP, etc.). Network Appearance - The Network Appearance uniquely identifies an SS7 entity (Point Code) into an SS7 network, as presented by the SG. It is used for the purposes of logically separating the signalling traffic between the SG and the Application Server Processes over a common SCTP association. This partitioning is necessary where an SG is logically partitioned to appear as end node elements in multiple separate SS7 networks, in which case there is a separate network appearance for each point code in the SS7 networks. It is also necessary when an SG is configured as an STP hosting multiple point codes, or when configured as multiple end nodes within the same network, in which case each point code is a separate network appearance.between the SG and the Application Server Processes over a common SCTP Association. An example is where an SG is logically partitioned to appear as an element in four separate national SS7 networks. A Network Appearance implicitly defines the SS7 Point Code(s), Network Indicator and MTP3 protocol type/variant/version used within a separate SS7 network. Network Byte Order: Most significant byte first, a.k.a Big Endian. Layer Management - Layer Management is a nodal function that handles the inputs and outputs between the M3UA layer and a local management entity. Host - The computing platform that the process (SGP, ASP or IPSP) is running on. Stream - A stream refers to an SCTP stream; a uni-directional logical channel established from one SCTP endpoint to another associated SCTP endpoint, within which all user messages are delivered in-sequence except for those submitted to the un-ordered delivery service. 1.3 M3UA Overview 1.3.1 Protocol Architecture. The framework architecture that has been defined for SCN signalling transport over IP [1] uses multiple components, including a common signalling transport protocol and an adaptation module to support the Sidebottom et al [Page 6] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 services expected by a particular SCN signalling protocol from its underlying protocol layer. Within the framework architecture, this document defines an MTP3-User adaptation module suitable for supporting the transfer of messages of any protocol layer that is identified to the MTP Level 3 as an MTP User. The list of these protocol layers include, but is not limited to, ISDN User Part (ISUP) [2,3,4], Signalling Connection Control Part (SCCP) [5,6,7] and Telephone User Part (TUP) [8]. TCAP [9,10,11] or RANAP [12] messages are transferred transparently by the M3UA protocol as SCCP payload, as they are SCCP-User protocols. It is recommended that M3UA use the services of the Stream Control Transmission Protocol (SCTP) [13] as the underlying reliable common signalling transport protocol. This is to take advantage of various SCTP features such as: - Explicit packet-oriented delivery (not stream-oriented), - Sequenced delivery of user messages within multiple streams, with an option for order-of-arrival delivery of individual user messages, - Optional multiplexing of user messages into SCTP datagrams, - Network-level fault tolerance through support of multi-homing at either or both ends of an association, - Resistance to flooding and masquerade attacks, and - Data segmentation to conform to discovered path MTU size. Under certain scenarios, such as back-to-back connections without redundancy requirements, the SCTP functions above MAY NOT be a requirement and TCP can be used as the underlying common transport protocol. 1.3.2 Services Provided by the M3UA Layer The M3UA Layer at an ASP or IPSP provides the equivalent set of primitives at its upper layer to the MTP3-Users as provided by the MTP Level 3 to its local MTP3-Users at an SS7 SEP. In this way, the ISUP and/or SCCP layer at an ASP or IPSP is unaware that the expected MTP3 services are offered remotely from an MTP3 Layer at an SGP, and not by a local MTP3 layer. The MTP3 layer at an SGP may also be unaware that its local users are actually remote user parts over M3UA. In effect, the M3UA extends access to the MTP3 layer services to a remote IP-based application. The M3UA layer does not itself provide the MTP3 services. However, in the case where an ASP is connected to more than one SGP, the M3UA layer at an ASP should maintain the status of configured SS7 destinations and route messages according to the availability and congestion status of the routes to these destinations via each SGP. Sidebottom et al [Page 7] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The M3UA layer may also be used for point-to-point signalling between two IP Server Processes (IPSPs). In this case, the M3UA layer provides the same set of primitives and services at its upper layer as the MTP3. However, in this case the expected MTP3 services are not offered remotely from an SGP. The MTP3 services are provided but the procedures to support these services are a subset of the MTP3 procedures due to the simplified point-to-point nature of the IPSP to IPSP relationship. 1.3.2.1 Support for the Transport of MTP3-User Messages The M3UA layer provides the transport of MTP-TRANSFER primitives across an established SCTP association between an SGP and an ASP or between IPSPs. The MTP-TRANSFER primitive information is encoded as in MTP3-User messages. In this way, the User Part messages received from the SS7 network by the SGP are not re-encoded into a different format for transport between the M3UA peers. The MTP3 Service Information Octet (SIO) and Routing Label (OPC, DPC, and SLS) are included, encoded as expected by the MTP3 and MTP3-User protocol layer. At an ASP, in the case where a destination is reachable via multiple SGPs, the M3UA layer must also choose via which SGP the message is to be routed or support load balancing across the SGPs, ensuring that no missequencing occurs. The M3UA layer does not impose a 272-octet signalling information field (SIF) length limit as specified by the SS7 MTP Level 2 protocol [14] [15] [16]. Larger information blocks can be accommodated directly by M3UA/SCTP, without the need for an upper layer segmentation/re-assembly procedure as specified in recent SCCP or ISUP versions. However, in the context of an SG, the maximum 272-octet block size must be followed when inter-working to a SS7 network that does not support the transfer of larger information blocks to the final destination. This avoids potential ISUP or SCCP fragmentation requirements at the SGPs. However, if the SS7 network is provisioned to support the Broadband MTP [20] to the final SS7 destination, the information block size limit MAY be increased past 272 octets. 1.3.2.2 Native Management Functions The M3UA layer provides the capability to indicate errors associated with received M3UA messages and to notify, as appropriate, local management and/or the peer M3UA. Sidebottom et al [Page 8] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 1.3.2.3 Inter-working with MTP3 Network Management Functions At the SGP, the M3UA layer must also provide inter-working with MTP3 management functions to support seamless operation of the user SCN signalling applications in the SS7 and IP domains. This includes: - Providing an indication to MTP3-Users at an ASP that a destination in the SS7 network is not reachable. - Providing an indication to MTP3-Users at an ASP that a destination in the SS7 network is now reachable. - Providing an indication to MTP3-Users at an ASP that messages to a destination in the SS7 network are experiencing SS7 congestion. - Providing an indication to the M3UA layer at an ASP that the routes to a destination in the SS7 network are restricted. - Providing an indication to MTP3-Users at an ASP that a MTP3-User peer is unavailable. The M3UA layer at an ASP keeps the state of the routes to remote SS7 destinations and may initiate an audit of the availability, the restricted or the congested state of remote SS7 destinations. This information is requested from the M3UA layer at the SGP. The M3UA layer at an ASP may also indicate to the SG that the M3UA layer itself or the ASP or the ASP's Host is congested. 1.3.2.4 Support for the Management of SCTP Associations between the SGP and ASPs. The M3UA layer at the SGP maintains the availability state of all configured remote ASPs, to manage the SCTP Associations and the traffic between the M3UA peers. As well, the active/inactive and congestion state of remote ASPs is maintained. The M3UA layer MAY be instructed by local management to establish an SCTP association to a peer M3UA node. This can be achieved using the M-SCTP_ESTABLISH primitives to request, indicate and confirm the establishment of an SCTP association with a peer M3UA node. In order to avoid redundant SCTP associations between two M3UA peers, one side (client) SHOULD be designated to establish the SCTP association, or M3UA configuration information maintained to detect redundant associations (e.g., via knowledge of the expected local and remote SCTP endpoint addresses). Local management MAY request from the M3UA layer the status of the underlying SCTP associations using the M-SCTP_STATUS request and Sidebottom et al [Page 9] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 confirm primitives. Also, the M3UA MAY autonomously inform local management of the reason for the release of an SCTP association, determined either locally within the M3UA layer or by a primitive from the SCTP. Also the M3UA layer MAY inform the local management of the change in status of an ASP or AS. This MAY be achieved using the M-ASP_STATUS request or M-AS_STATUS request primitives. 1.3.2.5 Support for the Management of Connections to Multiple SGPs As shown in Figure 1 an ASP may be connected to multiple SGPs. In such a case a particular SS7 destination may be reachable via more than one SGP, i.e., via more than one route. As MTP3 users only maintain status on a destination and not on a route basis, the M3UA layer must maintain the status (availability, restriction, and/or congestion of route to destination) of the individual routes, derive the overall availability or congestion status of the destination from the status of the individual routes, and inform the MTP3 users of this derived status whenever it changes. 1.3.3 Signalling Network Architecture A Signalling Gateway is used to support the transport of MTP3-User signalling traffic received from the SS7 network to multiple distributed ASPs (e.g., MGCs and IP Databases). Clearly, the M3UA protocol is not designed to meet the performance and reliability requirements for such transport by itself. However, the conjunction of distributed architecture and redundant networks does allow for a sufficiently reliable transport of signalling traffic over IP. The M3UA protocol is flexible enough to allow its operation and management in a variety of physical configurations, enabling Network Operators to meet their performance and reliability requirements. To meet the stringent SS7 signalling reliability and performance requirements for carrier grade networks, Network Operators SHOULD ensure that no single point of failure is present in the end-to-end network architecture between an SS7 node and an IP-based application. This can typically be achieved through the use of redundant SGPs or SGs, redundant hosts, and the provision of redundant QOS-bounded IP network paths for SCTP Associations between SCTP End Points. Obviously, the reliability of the SG, the MGC and other IP-based functional elements also needs to be taken into account. The distribution of ASPs and SGPs within the available Hosts MAY also be considered. As an example, for a particular Application Server, the related ASPs SHOULD be distributed over at least two Hosts. One example of a physical network architecture relevant to SS7 carrier- grade operation in the IP network domain is shown in Figure 1 below: Sidebottom et al [Page 10] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 SG MGC Host#1 ************** ************** Host#3 = * ********__*__________________________*__******** * = * * SGP1 *__*_____ _______________*__* ASP1 * * MGC1 * ******** * \ / * ******** * * ********__*______\__/________________*__******** * * * SGP2 *__*_______\/______ _____*__* ASP2 * * * ******** * /\ | | * ******** * * : * / \ | | * : * * ******** * / \ | | * ******** * * * SGPn * * | | | | * * ASPn * * * ******** * | | | | * ******** * ************** | | | | ************** | | \ / Host#2 ************** | | \ / ************** Host#4 = * ********__*_____| |______\/_______*__******** * = * * SGP1 *__*_________________/\_______*__* ASP1 * * MGC2 * ******** * / \ * ******** * * ********__*_______________/ \_____*__******** * * * SGP2 *__*__________________________*__* ASP2 * * * ******** * * ******** * * : * SCTP Associations * : * * ******** * * ******** * * * SGPn * * * * ASPn * * * ******** * * ******** * ************** ************** Figure 1 - Physical Model In this model, each host MAY have many application processes. In the case of the MGC, an ASP may provide service to one or more Application Servers, and is identified as an SCTP end point. A pair of Signalling Gateway Processes MAY represent, as an example, a single Signalling Gateway, serving a signalling point management cluster. This example model can also be applied to IPSP-IPSP signalling. In this case, each IPSP MAY have its services distributed across 2 hosts or more, and may have multiple server processes on each host. In the example above, each signalling process (SGP, ASP or IPSP) is the end point to more than one SCTP association, leading to more than one other signalling processes. To support this, a signalling process must be able to support distribution of M3UA messages to many simultaneous active associations. This message distribution function is based on the status of provisioned Routing Keys, the status of the signalling routes to signalling points in the SS7 network , and the redundancy model (active-standby, load-sharing, broadcast, n+k) of the remote signalling processes. Sidebottom et al [Page 11] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 For carrier grade networks, the failure or isolation of a particular signalling process should not cause stable calls or transactions to be lost. This implies that signalling processes need, in some cases, to share the call/transaction state or be able to pass the call state information between each other. In the case of ASPs performing call processing, coordination may also be required with the related Media Gateway to transfer the MGC control for a particular trunk termination. However, this sharing or communication of call/transaction state information is outside the scope of this document. This model serves as an example. M3UA imposes no restrictions as to the exact layout of the network elements, the message distribution algorithms and the distribution of the signalling processes. Instead, it provides a framework and a set of messages that allow for a flexible and scalable signalling network architecture, aiming to provide reliability and performance. 1.4 Functional Areas 1.4.1 Signalling Point Code Representation For example, within an SS7 network, a Signalling Gateway might be charged with representing a set of nodes in the IP domain into the SS7 network for routing purposes. The SG itself, as a signalling point in the SS7 network, might also be addressable with an SS7 Point Code for MTP3 Management purposes. The SG Point Code might also be used for addressing any local MTP3-Users at the SG such as an SG-resident SCCP function. An SG may be logically partitioned to operate in multiple SS7 network appearances. In such a case, the SG could be addressable with a Point Code in each network appearance, and represents a set of nodes in the IP domain into each SS7 network. Alias Point Codes [15] may also be used within an SG network appearance. Where an SG contains more than one SGP, the MTP3 routeset, SPMC and remote AS/ASP states of each SGP SHOULD be coordinated across all the SGPs. Re-routing of traffic between the SGPs SHOULD also be supported. Application Servers can be represented under the same Point Code of the SG, their own individual Point Codes or grouped with other Application Servers for Point Code preservation purposes. A single Point Code may be used to represent the SG and all the Application Servers together, if desired. If an ASP or group of ASPs is available to the SS7 network via more than one SG, each with its own Point Code, the ASP(s) will typically be represented by a Point Code that is separate from any SG Point Code. This allows, for example, these SGs to be viewed from the SS7 network as "STPs", each Sidebottom et al [Page 12] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 having an ongoing "route" to the same ASP(s). Under failure conditions where the ASP(s) become(s) unavailable from one of the SGs, this approach enables MTP3 route management messaging between the SG and SS7 network, allowing simple SS7 re-routing through an alternate SG without changing the Destination Point Code Address of SS7 traffic to the ASP(s). Where an AS can be reached via more than one SGP the corresponding Routing Keys in the involved SGPs should be identical. (Note: It is possible for the SGP Routing Key configuration data to be temporarily out-of-synch during configuration updates). +--------+ | | +------------+ SG 1 +--------------+ +-------+ | SS7 links | "STP" | IP network | ---- | SEP +---+ +--------+ +---/ \ | or | * | ASPs | | STP +---+ +--------+ +---\ / +-------+ | | | | ---- +------------+ SG 2 +--------------+ | "STP" | +--------+ * Note:. SG-to -SG communication is recommended for carrier grade networks, using an MTP3 linkset or an equivalent, to allow re-routing between the SGs in the event of route failures. Where SGPs are used, inter-SGP communication is recommended. Inter-SGP protocol is outside of the scope of this document. The following example shows a signalling gateway partitioned into two network appearances. SG +-------+ +---------------+ | SEP +--------------| SS7 Ntwk |M3UA| ---- +-------+ SS7 links | "A" | | / \ |__________| +-----------+ ASPs | | | | \ / +-------+ | SS7 Ntwk | | ---- | SEP +--------------+ "B" | | +-------+ +---------------+ 1.4.2 Routing Contexts and Routing Keys 1.4.2.1 Overview The distribution of SS7 messages between the SGP and the Application Servers is determined by the Routing Keys and their associated Routing Contexts. A Routing Key is essentially a set of SS7 parameters used to Sidebottom et al [Page 13] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 filter SS7 messages, whereas the Routing Context parameter is a 4-byte value (integer) that is associated to that Routing Key in a 1:1 relationship. The Routing Context therefore can be viewed as an index into a sending node's Message Distribution Table containing the Routing Key entries. Possible SS7 address/routing information that comprise a Routing Key entry includes, for example, the OPC, DPC, SIO found in the MTP3 routing label, or MTP3-User specific fields (such as the ISUP CIC, SCCP subsystem number) or TCAP transaction ID. Some example Routing Keys are: the DPC alone, the DPC/OPC combination, the DPC/OPC/CIC combination, or the DPC/SSN combination. The particular information used to define an M3UA Routing Key is application and network dependent, and none of the above examples are mandated. An Application Server Process may be configured to process signalling traffic related to more than one Application Server, over a single SCTP Association. In ASP Active and ASP Inactive management messages, the signalling traffic to be started or stopped is discriminated by the Routing Context parameter. At an ASP, the Routing Context parameter uniquely identifies the range of signalling traffic associated with each Application Server that the ASP is configured to receive. 1.4.2.2 Routing Key Limitations Routing Keys SHOULD be unique in the sense that each received SS7 signalling message SHOULD have a full or partial match to a single routing result to an Application Server. It is not necessary for the parameter range values within a particular Routing Key to be contiguous. For example, an AS could be configured to support call processing for multiple ranges of PSTN trunks that are not represented by contiguous CIC values. 1.4.2.3 Managing Routing Contexts and Routing Keys There are two ways to provision a Routing Key at an SGP. A Routing Key may be configured statically using an implementation dependent management interface, or dynamically using the M3UA Routing Key registration procedure. When using a management interface to configure Routing Keys, the message distribution function within the SGP is not limited to the set of parameters defined in this document. Other implementation dependent distribution algorithms may be used. Sidebottom et al [Page 14] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 1.4.2.4 Message Distribution at the SGP To direct messages received from the SS7 MTP3 network to the appropriate IP destination, the SGP must perform a message distribution function using information from the received MTP3-User message. To support this message distribution, the SGP might, for example, maintain the equivalent of a network address translation table, mapping incoming SS7 message information to an Application Server for a particular application and range of traffic. This could be accomplished by comparing elements of the incoming SS7 message to currently defined Routing Keys in the SGP. These Routing Keys could in turn map directly to an Application Server that is enabled by one or more ASPs. These ASPs provide dynamic status information regarding their availability, traffic handling capability and congestion to the SGP using various management messages defined in the M3UA protocol. The list of ASPs in an AS is assumed to be dynamic, taking into account the availability, traffic handling capability and congestion status of the individual ASPs in the list, as well as configuration changes and possible fail-over mechanisms. Normally, one or more ASPs are active (i.e., currently processing traffic) in the AS but in certain failure and transition cases it is possible that there may be no active ASP available. Broadcast, load- sharing and backup scenarios are supported. When there is no matching Routing Key entry for an incoming SS7 message, a default treatment MAY be specified. Possible solutions are to provide a default Application Server at the SGP that directs all unallocated traffic to a (set of) default ASP(s), or to drop the message and provide a notification to layer management. The treatment of unallocated traffic is implementation dependent. 1.4.2.5 Message Distribution at the ASP The ASP must choose an SGP to direct a message to the SS7 network. This is accomplished by observing the Destination Point Code (and possibly other elements of the outgoing message such as the SLS value). Implementation Note: Where more than one route (or SGP) is possible for routing to the SS7 network, the ASP could, for example, maintain a dynamic table of available SGP routes for the SS7 destinations, taking into account the SS7 destination availability/restricted/congestion status received from the SGP(s), the availability status of the individual SGPs and configuration changes and fail-over mechanisms. There is, however, no M3UA messaging to manage the status of an SGP (e.g., SGP-Up/Down/Active/Inactive messaging). Whenever an SCTP Sidebottom et al [Page 15] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 association to an SGP exists, the SGP is assumed to be ready for the purposes of responding to M3UA ASPSM messages (Refer to Section 3). Every SGP of one SG ASP regarding one AS provides identical SS7 connectivity to this ASP. 1.4.3 SS7 and M3UA Interworking In the case of SS7 and M3UA inter-working, the M3UA adaptation layer is designed to provide an extension of the MTP3 defined user primitives. 1.4.3.1 Signalling Gateway SS7 Layers The SG is responsible for terminating MTP Level 3 of the SS7 protocol, and offering an IP-based extension to its users. >From an SS7 perspective, it is expected that the Signalling Gateway transmits and receives SS7 Message Signalling Units (MSUs) to and from the PSTN over a standard SS7 network interface, using the SS7 Message Transfer Part (MTP) [14,15,16] to provide reliable transport of the messages. As a standard SS7 network interface, the use of MTP Level 2 signalling links is not the only possibility. ATM-based High Speed Links can also be used with the services of the Signalling ATM Adaptation Layer (SAAL) [17,18]. Note: It is also possible for IP-based interfaces to be present, using the services of the MTP2-User Adaptation Layer (M2UA) [26] or M2PA [27]. These could be terminated at a Signalling Transfer Point (STP) or Signalling End Point (SEP). Using the services of MTP3, the SG could be capable of communicating with remote SS7 SEPs in a quasi-associated fashion, where STPs may be present in the SS7 path between the SEP and the SG. 1.4.3.2 SS7 and M3UA Inter-Working at the SG The SGP provides a functional inter-working of transport functions between the SS7 network and the IP network by also supporting the M3UA adaptation layer. It allows the transfer of MTP3-User signalling messages to and from an IP-based Application Server Process where the peer MTP3-User protocol layer exists. Sidebottom et al [Page 16] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 For SS7 user part management, it is required that the MTP3-User protocols at ASPs receive indications of SS7 signalling point availability, SS7 network congestion, and remote User Part unavailability as would be expected in an SS7 SEP node. To accomplish this, the MTP-PAUSE, MTP-RESUME and MTP-STATUS indication primitives received at the MTP3 upper layer interface at the SG need to be propagated to the remote MTP3-User lower layer interface at the ASP. MTP3 management messages (such as TFPs or TFAs received from the SS7 network) MUST NOT be encapsulated as Data message Payload Data and sent either from SG to ASP or from ASP to SG. The SG MUST terminate these messages and generate M3UA messages as appropriate. 1.4.3.3 Application Server A cluster of application servers is responsible for providing the overall support for one or more SS7 upper layers. From an SS7 standpoint, a Signalling Point Management Cluster (SPMC) provides complete support for the upper layer service for a given point code. As an example, an SPMC providing MGC capabilities could provide complete support for ISUP (and any other MTP3 user located at the point code of the SPMC) for a given point code. In the case where an ASP is connected to more than one SGP, the M3UA layer must maintain the status of configured SS7 destinations and route messages according to availability/congestion/restricted status of the routes to these SS7 destinations. 1.4.3.4 IPSP Considerations Since IPSPs use M3UA in a point-to-point fashion, there is no concept of routing of messages beyond the remote end. Therefore, SS7 and M3UA inter-working is not necessary for this model. 1.4.4 Redundancy Models 1.4.4.1 Application Server Redundancy All MTP3-User messages (e.g., ISUP, SCCP) which match a provisioned Routing Key at an SGP are mapped to an Application Server. Sidebottom et al [Page 17] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The Application Server is the set of all ASPs associated with a specific Routing Key. Each ASP in this set may be active inactive or unavailable. Active ASPs handle traffic; inactive ASPs might be used when active ASPs become unavailable. The fail-over model supports an "n+k" redundancy model, where "n" ASPs is the minimum number of redundant ASPs required to handle traffic and "k" ASPs are available to take over for a failed or unavailable ASP. A "1+1" active/back-up redundancy is a subset of this model. A simplex "1+0" model is also supported as a subset, with no ASP redundancy. At the SGP, an Application Server list contains active and inactive ASPs to support ASP broadcast, load-sharing and fail-over procedures. The list of ASPs within a logical Application Server is kept updated in the SGP to reflect the active Application Server Process(es). For example, in the network shown in Figure 1, all messages to DPC x could be sent to ASP1 in Host3 or ASP1 in Host4. The AS list at SGP1 in Host 1 might look like the following: Routing Key {DPC=x) - "Application Server #1" ASP1/Host3 - State = Active ASP1/Host4 - State = Inactive In this "1+1" redundancy case, ASP1 in Host3 would be sent any incoming message with DPC=x. ASP1 in Host4 would normally be brought to the "active" state upon failure of, or loss of connectivity to, ASP1/Host1. The AS List at SGP1 in Host1 might also be set up in load-share mode: Routing Key {DPC=x) - "Application Server #1" ASP1/Host3 - State = Active ASP1/Host4 - State = Active In this case, both the ASPs would be sent a portion of the traffic. For example the two ASPs could together form a database, where incoming queries may be sent to any active ASP. Care might need to be exercised by a Network Operator in the selection of the routing information to be used as the Routing Key for a particular AS. Sidebottom et al [Page 18] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 For example, where Application Servers are defined using ranges of ISUP CIC values, the Operator is implicitly splitting up control of the related circuit groups. Some CIC value range assignments may interfere with ISUP circuit group management procedures. In the process of fail-over, it is recommended that in the case of ASPs supporting call processing, stable calls do not fail. It is possible that calls in "transition" MAY fail, although measures of communication between the ASPs involved can be used to mitigate this. For example, the two ASPs MAY share call state via shared memory, or MAY use an ASP to ASP protocol to pass call state information. Any ASP-to-ASP protocol to support this function is outside the scope of this document. 1.4.4.2 Signalling Gateway Redundancy Signalling Gateways MAY also be distributed over multiple hosts. Much like the AS model, SGs may comprise one or more SG Processes (SGPs), distributed over one or more hosts, using an active/back-up or a load- sharing model. Also, every SGP within an SG communicating with an ASP provides identical SS7 connectivity to this ASP. Should an SGP lose all or partial SS7 connectivity and other SGPs exist, the SGP MUST terminate the SCTP associations to the concerned ASPs. It is therefore possible for an ASP to route signalling messages destined to the SS7 network using more than one SGP. In this model, a Signalling Gateway is deployed as a cluster of hosts acting as a single SG. A primary/back-up redundancy model is possible, where the unavailability of the SCTP association to a primary SGP could be used to reroute affected traffic to an alternate SGP. A load-sharing model is possible, where the signalling messages are load-shared between multiple SGPs. A broadcast model is also possible, where signalling messages are sent to each active SGP in the SG. The distribution of the MTP3-user messages over the SGPs should be done in such a way to minimize message mis-sequencing, as required by the SS7 User Parts. It may also be possible for an ASP to use more than one SG to access a specific SS7 end point, in a model that resembles an SS7 STP mated pair. Typically, SS7 STPs are deployed in mated pairs, with traffic load-shared between them. Other models are also possible, subject to the limitations of the local SS7 network provisioning guidelines. >From the perspective of the M3UA layer at an ASP, a particular SG is capable of transferring traffic to an SS7 destination if an SCTP association with at least one SGP of the SG is established, the SGP has returned an acknowledgement to the ASP to indicate that the ASP is actively handling traffic for that destination, and the SGP has not indicated that the destination is inaccessible. When an ASP is configured to use multiple SGPs for transferring traffic to the SS7 network, the ASP must maintain knowledge of the current capability of the SGPs to handle traffic to destinations of interest. This information is crucial to the overall reliability of the service, for Sidebottom et al [Page 19] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 active/back-up, load-sharing and broadcast models, in the event of failures, recovery and maintenance activities. The ASP M3UA may also use this information for congestion avoidance purposes. The distribution of the MTP3-user messages over the SGPs should be done in such a way to minimize message mis-sequencing, as required by the SS7 User Parts. 1.4.5 Flow Control Local Management at an ASP may wish to stop traffic across an SCTP association to temporarily remove the association from service or to perform testing and maintenance activity. The function could optionally be used to control the start of traffic on to a newly available SCTP association. 1.4.6 Congestion Management The M3UA layer is informed of local and IP network congestion by means of an implementation-dependent function (e.g., an implementation- dependent indication from the SCTP of IP network congestion). At an ASP or IPSP, the M3UA layer indicates congestion to local MTP3- Users by means of an MTP-STATUS primitive, as per current MTP3 procedures, to invoke appropriate upper layer responses. When an SG determines that the transport of SS7 messages to a Signalling Point Management Cluster (SPMC) is encountering congestion, the SG MAY trigger SS7 MTP3 Transfer Controlled management messages to originating SS7 nodes, per the congestion procedures of the relevant MTP3 standard. The triggering of SS7 MTP3 Management messages from an SG is an implementation-dependent function. The M3UA layer at an ASP or IPSP MAY indicate local congestion to an M3UA peer with an SCON message. When an SG receives a congestion message (SCON) from an ASP, and the SG determines that an SPMC is now encountering congestion, it MAY trigger SS7 MTP3 Transfer Controlled management messages to concerned SS7 destinations according to congestion procedures of the relevant MTP3 standard. 1.4.7 SCTP Stream Mapping. The M3UA layer at both the SGP and ASP also supports the assignment of signalling traffic into streams within an SCTP association. Traffic that requires sequencing SHOULD be assigned to the same stream. To accomplish this, MTP3-User traffic may be assigned to individual streams based on, for example, the SLS value in the MTP3 Routing Label or the ISUP CIC assignment, subject of course to the maximum number of streams supported by the underlying SCTP association. Sidebottom et al [Page 20] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 1.4.8 Client/Server Model It is recommended that the SGP and ASP be able to support both client and server operation. The peer endpoints using M3UA SHOULD be configured so that one always takes on the role of client and the other the role of server for initiating SCTP associations. The default orientation would be for the SGP to take on the role of server while the ASP is the client. In this case, ASPs SHOULD initiate the SCTP association to the SGP In the case of IPSP to IPSP communication, the peer endpoints using M3UA SHOULD be configured so that one always takes on the role of client and the other the role of server for initiating SCTP associations. The SCTP Registered User Port Number Assignment for M3UA is 2905. 1.5 Sample Configurations 1.5.1 Example 1: ISUP Message Transport ******** SS7 ***************** IP ******** * SEP *---------* SGP *--------* ASP * ******** ***************** ******** +------+ +---------------+ +------+ | ISUP | | (NIF) | | ISUP | +------+ +------+ +------+ +------+ | MTP3 | | MTP3 | | M3UA | | M3UA | +------| +------+-+------+ +------+ | MTP2 | | MTP2 | | SCTP | | SCTP | +------+ +------+ +------+ +------+ | L1 | | L1 | | IP | | IP | +------+ +------+ +------+ +------+ |_______________| |______________| SEP - SS7 Signalling End Point SCTP - Stream Control Transmission Protocol NIF - Nodal Inter-working Function In this example, the SGP provides an implementation-dependent nodal inter-working function (NIF) that allows the MGC to exchange SS7 signalling messages with the SS7-based SEP. The NIF within the SGP serves as the interface within the SGP between the MTP3 and M3UA. This nodal inter-working function has no visible peer protocol with either the MGC or SEP. It also provides network status information to one or both sides of the network. Sidebottom et al [Page 21] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 For internal SGP modeling purposes, at the NIF level, SS7 signalling messages that are destined to the MGC are received as MTP-TRANSFER indication primitives from the MTP Level 3 upper layer interface, translated to MTP-TRANSFER request primitives, and sent to the local M3UA-resident message distribution function for ongoing routing to the final IP destination. Messages received from the local M3UA network address translation and mapping function as MTP-TRANSFER indication primitives are sent to the MTP Level 3 upper layer interface as MTP- TRANSFER request primitives for on-going MTP Level 3 routing to an SS7 SEP. For the purposes of providing SS7 network status information the NIF also delivers MTP-PAUSE, MTP-RESUME and MTP-STATUS indication primitives received from the MTP Level 3 upper layer interface to the local M3UA-resident management function. In addition, as an implementation and network option, restricted destinations are communicated from MTP network management to the local M3UA-resident management function. 1.5.2 Example 2: SCCP Transport between IPSPs ******** IP ******** * IPSP * * IPSP * ******** ******** +------+ +------+ |SCCP- | |SCCP- | | User | | User | +------+ +------+ | SCCP | | SCCP | +------+ +------+ | M3UA | | M3UA | +------+ +------+ | SCTP | | SCTP | +------+ +------+ | IP | | IP | +------+ +------+ |________________| This example shows an architecture where no Signalling Gateway is used. In this example, SCCP messages are exchanged directly between two IP- resident IPSPs with resident SCCP-User protocol instances, such as RANAP or TCAP. SS7 network inter-working is not required, therefore there is no MTP3 network management status information for the SCCP and SCCP-User protocols to consider. Any MTP-PAUSE, MTP-RESUME or MTP- STATUS indications from the M3UA layer to the SCCP layer should consider the status of the SCTP Association and underlying IP network and any congestion information received from the remote site. Sidebottom et al [Page 22] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 1.5.3 Example 3: SGP Resident SCCP Layer, with Remote ASP ******** SS7 ***************** IP ******** * SEP *---------* *--------* * * or * * SGP * * ASP * * STP * * * * * ******** ***************** ******** +------+ +---------------+ +------+ | SCCP-| | SCCP | | SCCP-| | User | +---------------+ | User | +------+ | _____ | +------+ | SCCP | | | | | | SCCP | +------+ +------+-+------+ +------+ | MTP3 | | MTP3 | | M3UA | | M3UA | +------| +------+ +------+ +------+ | MTP2 | | MTP2 | | SCTP | | SCTP | +------+ +------+ +------+ +------+ | L1 | | L1 | | IP | | IP | +------+ +------+ +------+ +------+ |_______________| |______________| STP - SS7 Signalling Transfer Point In this example, the SGP contains an instance of the SS7 SCCP protocol layer that may, for example, perform the SCCP Global Title Translation (GTT) function for messages logically addressed to the SG SCCP. If the result of a GTT for an SCCP message yields an SS7 DPC or DPC/SSN address of an SCCP peer located in the IP domain, the resulting MTP- TRANSFER request primitive is sent to the local M3UA-resident network address translation and mapping function for ongoing routing to the final IP destination. Similarly, the SCCP instance in an SGP can perform the SCCP GTT service for messages logically addressed to it from SCCP peers in the IP domain. In this case, MTP-TRANSFER indication primitives are sent from the local M3UA-resident network address translation and mapping function to the SCCP for GTT. If the result of the GTT yields the address of an SCCP peer in the SS7 network then the resulting MTP- TRANSFER request primitive is given to the MTP3 for delivery to an SS7- resident node. It is possible that the above SCCP GTT at the SGP could yield the address of an SCCP peer in the IP domain and the resulting MTP-TRANSFER request primitive would be sent back to the M3UA layer for delivery to an IP destination. For internal SGP modeling purposes, this may be accomplished with the use of an implementation-dependent nodal inter-working function within the SGP that effectively sits below the SCCP and routes MTP-TRANSFER Sidebottom et al [Page 23] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 request/indication messages to/from both the MTP3 and the M3UA layer, based on the SS7 DPC or DPC/SSN address information. This nodal inter- working function has no visible peer protocol with either the ASP or SEP. Note that the services and interface provided by the M3UA layer are the same as in Example 1 and the functions taking place in the SCCP entity are transparent to the M3UA layer. The SCCP protocol functions are not reproduced in the M3UA protocol. 1.6 Definition of M3UA Boundaries 1.6.1 Definition of the Boundary between M3UA and an MTP3-User. >From ITU Q.701 [14]: MTP-TRANSFER request MTP-TRANSFER indication MTP-PAUSE indication MTP-RESUME indication MTP-STATUS indication 1.6.2 Definition of the Boundary between M3UA and SCTP An example of the upper layer primitives provided by the SCTP are provided in Reference [13] Section 10. 1.6.3 Definition of the Boundary between M3UA and Layer Management M-SCTP_ESTABLISH request Direction: LM -> M3UA Purpose: LM requests ASP to establish an SCTP association with its peer. M-STCP_ESTABLISH confirm Direction: M3UA -> LM Purpose: ASP confirms to LM that it has established an SCTP association with its peer. M-SCTP_ESTABLISH indication Direction: M3UA -> LM Purpose: M3UA informs LM that a remote ASP has established an SCTP association. M-SCTP_RELEASE request Direction: LM -> M3UA Purpose: LM requests ASP to release an SCTP association with its peer. Sidebottom et al [Page 24] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 M-SCTP_RELEASE confirm Direction: M3UA -> LM Purpose: ASP confirms to LM that it has released SCTP association with its peer. M-SCTP_RELEASE indication Direction: M3UA -> LM Purpose: M3UA informs LM that a remote ASP has released an SCTP Association or the SCTP association has failed. M-SCTP RESTART indication Direction: M3UA -> LM Purpose: M3UA informs LM that an SCTP restart indication has been received. M-SCTP_STATUS request Direction: LM -> M3UA Purpose: LM requests M3UA to report the status of an SCTP association. M-SCTP_STATUS confirm Direction: M3UA -> LM Purpose: M3UA responds with the status of an SCTP association. M-SCTP STATUS indication Direction: M3UA -> LM Purpose: M3UA reports the status of an SCTP association. M-ASP_STATUS request Direction: LM -> M3UA Purpose: LM requests M3UA to report the status of a local or remote ASP. M-ASP_STATUS confirm Direction: M3UA -> LM Purpose: M3UA reports status of local or remote ASP. M-AS_STATUS request Direction: LM -> M3UA Purpose: LM requests M3UA to report the status of an AS. M-AS_STATUS confirm Direction: M3UA -> LM Purpose: M3UA reports the status of an AS. M-NOTIFY indication Direction: M3UA -> LM Purpose: M3UA reports that it has received a Notify message from its peer. M-ERROR indication Direction: M3UA -> LM Purpose: M3UA reports that it has received an Error message from its peer or that a local operation has been unsuccessful. Sidebottom et al [Page 25] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 M-ASP_UP request Direction: LM -> M3UA Purpose: LM requests ASP to start its operation and send an ASP Up message to its peer. M-ASP_UP confirm Direction: M3UA -> LM Purpose: ASP reports that is has received an ASP UP Ack message from its peer. M-ASP_UP indication Direction: M3UA -> LM Purpose: M3UA reports it has successfully processed an incoming ASP Up message from its peer. M-ASP_DOWN request Direction: LM -> M3UA Purpose: LM requests ASP to stop its operation and send an ASP-Down message to its peer. M-ASP_DOWN confirm Direction: M3UA -> LM Purpose: ASP reports that is has received an ASP Down Ack message from its peer. M-ASP_DOWN indication Direction: M3UA -> LM Purpose: M3UA reports it has successfully processed an incoming ASP Down message from its peer, or the SCTP association has been lost/reset. M-ASP_ACTIVE request Direction: LM -> M3UA Purpose: LM requests ASP to send an ASP Active message to its peer. M-ASP_ACTIVE confirm Direction: M3UA -> LM Purpose: ASP reports that is has received an ASP Active Ack message from its peer. M-ASP_ACTIVE indication Direction: M3UA -> LM Purpose: M3UA reports it has successfully processed an incoming ASP Active message from its peer. M-ASP_INACTIVE request Direction: LM -> M3UA Purpose: LM requests ASP to send an ASP Inactive message to its peer. Sidebottom et al [Page 26] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 M-ASP_INACTIVE confirm Direction: LM -> M3UA Purpose: ASP reports that is has received an ASP Inactive Ack message from its peer. M-ASP_INACTIVE indication Direction: M3UA -> LM Purpose: M3UA reports it has successfully processed an incoming ASP Inactive message from its peer. M-AS_ACTIVE indication Direction: M3UA -> LM Purpose: M3UA reports that an AS has moved to the AS-ACTIVE state. M-AS_INACTIVE indication Direction: M3UA -> LM Purpose: M3UA reports that an AS has moved to the AS-INACTIVE state. M-AS_DOWN indication Direction: M3UA -> LM Purpose: M3UA reports that an AS has moved to the AS-DOWN state. If dynamic registration of RK is supported by the M3UA layer, the layer MAY support the following additional primitives: M-RK_REG request Direction: LM -> M3UA Purpose: LM requests ASP to register RK(s) with its peer by sending REG REQ message M-RK_REG confirm Direction: M3UA -> LM Purpose: ASP reports that it has received REG RSP message with registration status as successful from its peer. M-RK_REG indication Direction: M3UA -> LM Purpose: M3UA informs LM that it has successfully processed an incoming REG REQ message. M-RK_DEREG request Direction: LM -> M3UA Purpose: LM requests ASP to de-register RK(s) with its peer by sending DEREG REQ message. M-RK_DEREG confirm Direction: M3UA -> LM Purpose: ASP reports that it has received DEREG REQ message with de- registration status as successful from its peer. Sidebottom et al [Page 27] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 M-RK_DEREG indication Direction: M3UA -> LM Purpose: M3UA informs LM that it has successfully processed an incoming DEREG REQ from its peer. 2.0 Conventions The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD, SHOULD NOT, RECOMMENDED, NOT RECOMMENDED, MAY, and OPTIONAL, when they appear in this document, are to be interpreted as described in [RFC2119]. 3. M3UA Protocol Elements The general M3UA message format includes a Common Message Header followed by zero or more parameters as defined by the Message Type. For forward compatibility, all Message Types may have attached parameters even if none are specified in this version. 3.1 Common Message Header The protocol messages for MTP3-User Adaptation require a message header which contains the adaptation layer version, the message type, and message length. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Version | Reserved | Message Class | Message Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / / All fields in an M3UA message MUST be transmitted in the network byte order, unless otherwise stated. 3.1.1 M3UA Protocol Version: 8 bits (unsigned integer) The version field contains the version of the M3UA adaptation layer. The supported versions are the following: 1 Release 1.0 Sidebottom et al [Page 28] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 3.1.2 Message Classes and Types The following list contains the valid Message Classes: Message Class: 8 bits (unsigned integer) The following list contains the valid Message Type Classes: 0 Management (MGMT) Message 1 Transfer Messages 2 SS7 Signalling Network Management (SSNM) Messages 3 ASP State Maintenance (ASPSM) Messages 4 ASP Traffic Maintenance (ASPTM) Messages 5 Reserved for Other Sigtran Adaptation Layers 6 Reserved for Other Sigtran Adaptation Layers 7 Reserved for Other Sigtran Adaptation Layers 8 Reserved for Other Sigtran Adaptation Layers 9 Routing Key Management (RKM) Messages 10 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined Message Class extensions Message Type: 8 bits (unsigned integer) The following list contains the message types for the defined messages. Management (MGMT) Messages (See Section 3.6) 0 Error (ERR) 1 Notify (NTFY) 2 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined MGMT extensions Transfer Messages (See Section 3.3) 0 Reserved 1 Payload Data (DATA) 2 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined Transfer extensions SS7 Signalling Network Management (SSNM) Messages (See Section 3.4) 0 Reserved 1 Destination Unavailable (DUNA) 2 Destination Available (DAVA) 3 Destination State Audit (DAUD) 4 SS7 Network Congestion (SCON) 5 Destination User Part Unavailable (DUPU) 6 Destination Restricted (DRST) 7 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined SSNM extensions Sidebottom et al [Page 29] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 ASP State Maintenance (ASPSM) Messages (See Section 3.5) 0 Reserved 1 ASP Up (ASPUP) 2 ASP Down (ASPDN) 3 Heartbeat (BEAT) 4 ASP Up Acknowledgement (ASPUP ACK) 5 ASP Down Acknowledgement (ASPDN ACK) 6 Heatbeat Acknowledgement (BEAT ACK) 7 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined ASPSM extensions ASP Traffic Maintenance (ASPTM) Messages (See Section 3.5) 0 Reserved 1 ASP Active (ASPAC) 2 ASP Inactive (ASPIA) 3 ASP Active Acknowledgement (ASPAC ACK) 4 ASP Inactive Acknowledgement (ASPIA ACK) 5 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined ASPTM extensions Routing Key Management (RKM) Messages (See Section 3.7) 0 Reserved 1 Registration Request (REG REQ) 2 Registration Response (REG RSP) 3 Deregistration Request (DEREG REQ) 4 Deregistration Response (DEREG RSP) 5 to 127 Reserved by the IETF 128 to 255 Reserved for IETF-Defined RKM extensions 3.1.3 Reserved: 8 bits The Reserved field SHOULD be set to all '0's and ignored by the receiver. 3.1.4 Message Length: 32-bits (unsigned integer) The Message Length defines the length of the message in octets, including the Common Header. For messages with a final parameter containing padding, the parameter padding MUST be included in the Message Length. Note: A receiver SHOULD accept the message whether or not the final parameter padding is included in the message length. Sidebottom et al [Page 30] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 3.2 Variable-Length Parameter Format M3UA messages consist of a Common Header followed by zero or more variable length parameters, as defined by the message type. All the parameters contained in a message are defined in a Tag-Length-Value format as shown below. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Parameter Tag | Parameter Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Parameter Value / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Where more than one parameter is included in a message, the parameters may be in any order, except where explicitly mandated. A receiver SHOULD accept the parameters in any order. Parameter Tag: 16 bits (unsigned integer) The Tag field is a 16-bit identifier of the type of parameter. It takes a value of 0 to 65534. Common parameters used by adaptation layers are in the range of 0x00 to 0x3f. M3UA-specific parameters have Tags in the range 0x0200 to 0x02ff. The parameter Tags defined are as follows: 0x0000 Reserved 0x0200 Network Appearance 0x0201 Protocol Data 1 0x0202 Protocol Data 2 0x0004 INFO String 0x0203 Affected Destinations 0x0006 Routing Context 0x0007 Diagnostic Information 0x0009 Heartbeat Data 0x0204 User/Cause 0x000a Reason 0x000b Traffic Mode Type 0x000c Error Code 0x000d Status 0x000e ASP Identifier 0x0205 Congestion Indications 0x0206 Concerned Destination 0x0207 Routing Key 0x0208 Registration Result 0x0209 De-registration Result 0x020a Local_Routing Key Identifier 0x020b Destination Point Code 0x020c Service Indicators Sidebottom et al [Page 31] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 0x02 Subsystem Numbers 0x020e Originating Point Code List 0x020f Circuit Range 0x0210 to 0xffff...Reserved by the IETF The value of 65535 is reserved for IETF-defined extensions. Values other than those defined in specific parameter description are reserved for use by the IETF. Parameter Length: 16 bits (unsigned integer) The Parameter Length field contains the size of the parameter in bytes, including the Parameter Tag, Parameter Length, and Parameter Value fields. The Parameter Length does not include any padding bytes. Parameter Value: variable-length. The Parameter Value field contains the actual information to be transferred in the parameter. The total length of a parameter (including Tag, Parameter Length and Value fields) MUST be a multiple of 4 bytes. If the length of the parameter is not a multiple of 4 bytes, the sender pads the Parameter at the end (i.e., after the Parameter Value field) with all zero bytes. The length of the padding is NOT included in the parameter length field. A sender SHOULD NOT pad with more than 3 bytes. The receiver MUST ignore the padding bytes. 3.3 Transfer Messages The following section describes the Transfer messages and parameter contents. 3.3.1 Payload Data Message (DATA) The DATA message contains the SS7 MTP3-User protocol data, which is an MTP-TRANSFER primitive, including the complete MTP3 Routing Label. The DATA message contains the following variable length parameters: Network Appearance Optional Protocol Data 1 or 2 Mandatory Sidebottom et al [Page 32] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The following format MUST be used for the Data Message: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0200 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0201 or 0x0202 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Protocol Data / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Network Appearance: 32-bits (unsigned integer) The optional Network Appearance parameter identifies the SS7 network context for the message, for the purposes of logically separating the signalling traffic between the SGP and the ASP over a common SCTP association. An example is where an SG is logically partitioned to appear as an element in four different national SS7 networks. In a DATA message, the Network Appearance implicitly defines the SS7 Point Code format used, the SS7 Network Indicator value, and the MTP3 and possibly the MTP3-User protocol type/variant/version used within the specific SS7 network. Where an SG operates in the context of a single SS7 network, or individual SCTP associations are dedicated to each SS7 network context, the Network Appearance parameter is not required. In other cases the parameter MUST be included. The Network Appearance parameter value is of local significance only, coordinated between the SGP and ASP. Therefore, in the case where an ASP is connected to more than one SGP, the same SS7 network context may be identified by different Network Appearance values depending over which SGP a message is being transmitted/received. Where the optional Network Appearance parameter is present, it must be the first parameter in the message as it defines the format of the Protocol Data field One of two possible Protocol Data parameters are included in a DATA message: Protocol Data 1 or Protocol Data 2. Sidebottom et al [Page 33] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Protocol Data 1 or 2: variable length The Protocol Data 1 parameter contains the original SS7 MTP3 message, including the Service Information Octet and Routing Label. The Protocol Data 1 parameter contains the following fields: Service Information Octet. Includes: Service Indicator, Network Indicator, and Spare/Priority codes. Routing Label. Includes: Destination Point Code, Originating Point Code, And Signalling Link Selection Code (SLS). User Protocol Data. Includes: MTP3-User protocol elements (e.g., ISUP, SCCP, or TUP parameters). The Protocol Data 2 parameter contains all the information in Protocol Data 1 as described above, plus the MTP2 Length Indicator octet. The MTP2 Length Indicator (LI) octet appears before the SIO and Routing Label information. The MTP2 Length Indicator octet is required for some national MTP variants that use the spare bits in the LI to carry additional information of interest to the MTP3 and MTP3-User (e.g., the Japan TTC standard use of LI spare bits to indicate message priority) The Payload Data format is as defined in the relevant MTP standards for the SS7 protocol being transported. The format is either implicitly known or identified by the Network Appearance parameter. Note: In the SS7 Recommendations, the format of the messages and fields within the messages are based on bit transmission order. In these recommendations the Least Significant Bit (LSB) of each field is positioned to the right. The received SS7 fields are populated octet by octet as received into the 4-octet word as shown in the two examples below. For the ANSI protocol example, the Protocol Data 1 field format is shown below: Sidebottom et al [Page 34] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SIO | DPC Member | DPC Cluster | DPC Network | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OPC Member | OPC Cluster | OPC Network | SLS | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Protocol Data / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |MSB---------------------------------------------------------LSB| Within each octet the Least Significant Bit (LSB) per the SS7 Recommendations is to the right (e.g., bit 7 of SIO is the LSB). For the ITU international protocol example (with the 3/8/3 Point Code format), the Protocol Data 1 field is shown below. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SIO | DPC | DPC |OPC| DPC | DPC | OPC |@| | | Region *| SP *|SP*|Zone*| reg.| Region *| | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SLS | OPC |$| Protocol | | *|Zone*| | Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ * marks LSB of each field; @ = OPC SP MSB; $ = OPC region MSB 3.4 SS7 Signalling Network Management (SSNM) Messages 3.4.1 Destination Unavailable (DUNA) The DUNA message is sent from all SGPs in an SG to all concerned ASPs to indicate that the SG has determined that one or more SS7 destinations are unreachable. It is also sent by an SGP in response to a message from the ASP to an unreachable SS7 destination. As an implementation option the SG may suppress the sending of subsequent "response" DUNA messages regarding a certain unreachable SS7 destination for a certain period to give the remote side time to react. The MTP3-User at the ASP is expected to stop traffic to the affected destination through the SGPs initiating the DUNA message as per the defined MTP3-User procedures. Sidebottom et al [Page 35] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The DUNA message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory INFO String Optional The format for DUNA Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0200 | Length =8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0203 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / ... / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Network Appearance: 32-bit unsigned integer See Section 3.3.1 Affected Destinations: n x 32-bits The Affected Destinations parameter contains up to sixteen Affected Destination Point Code fields, each a three-octet parameter to allow for 14-, 16- and 24-bit binary formatted SS7 Point Codes. Affected Point Codes that are less than 24-bits, are padded on the left to the 24-bit boundary. The encoding is shown below for ANSI and ITU Point Code examples. Sidebottom et al [Page 36] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 ANSI 24-bit Point Code: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Network | Cluster | Member | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |MSB-----------------------------------------LSB| ITU 14-bit Point Code: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask |0 0 0 0 0 0 0 0 0 0|Zone | Region | SP | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |MSB--------------------LSB| It is optional to send an Affected Destinations parameter with more than one Affected DPC but it is mandatory to receive and process it. All the Affected DPCs included must be within the same Network Appearance. Including multiple Affected DPCs may be useful when reception of an MTP3 management message or a linkset event simultaneously affects the availability status of a list of destinations at an SG. Mask: 8-bits (unsigned integer) The Mask field associated with each Affected DPC in the Affected Destinations parameter, used to identify a contiguous range of Affected Destination Point Codes, independent of the point code format. Identifying a contiguous range of Affected DPCs may be useful when reception of an MTP3 management message or a linkset event simultaneously affects the availability status of a series of destinations at an SG. For example, if all DPCs in an ANSI cluster are determined to be unavailable due to local linkset unavailability, the DUNA could identify potentially 256 Affected DPCs in a single Affected DPC field. The Mask parameter represents a bit mask that can be applied to the related Affected DPC field. The bit mask identifies how many bits of the Affected DPC field are significant and which are effectively "wildcarded". For example, a mask of "8" indicates that the least significant eight bits of the DPC is "wildcarded". For an ANSI 24- bit Affected DPC, this is equivalent to signalling that all DPCs in an ANSI Cluster are unavailable. A mask of "3" indicates that the least significant three bits of the DPC is "wildcarded". For a 14- bit ITU Affected DPC, this is equivalent to signaling that an ITU Sidebottom et al [Page 37] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Region is unavailable. A mask value equal to the number of bits in the DPC indicates that the entire network appearance is affected - this is used to indicate network isolation to the ASP. INFO String: variable length The optional INFO String parameter can carry any 8-bit ASCII character string along with the message. Length of the INFO String parameter is from 0 to 255 characters. No procedures are presently identified for its use but the INFO String MAY be used by Operators to identify in text form the location reflected by the Affected DPC for debugging purposes. 3.4.2 Destination Available (DAVA) The DAVA message is sent from the SGP to all concerned ASPs to indicate that the SG has determined that one or more SS7 destinations are now reachable (and not restricted), or in response to a DAUD message if appropriate. The ASP MTP3-User protocol is informed and may now resume traffic to the affected destination. The ASP M3UA layer routes the MTP3_user traffic through the SGP(s) initiating the DAVA message. The DAVA message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory INFO String Optional The format and description of the Network Appearance, Affected Destinations and INFO String parameters is the same as for the DUNA message (See Section 3.4.1). 3.4.3 Destination State Audit (DAUD) The DAUD message MAY be sent from the ASP to the SGP to audit the availability/congestion state of SS7 routes to one or more affected destinations. The DAUD message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory INFO String Optional The format and description of DAUD Message parameters is the same as for the DUNA message (See Section 3.4.1). 3.4.4 SS7 Network Congestion (SCON) The SCON message can be sent from the SGP to all concerned ASPs to indicate congestion in the SS7 network to one or more destinations, or Sidebottom et al [Page 38] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 to an ASP in response to a DATA or DAUD message as appropriate. For some MTP protocol variants (e.g., ANSI MTP) the SCON message may be sent when the SS7 congestion level changes. The SCON message MAY also be sent from the M3UA layer of an ASP to an M3UA peer indicating that the M3UA layer or the ASP is congested. The SCON message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory Concerned Destination Optional Congestion Indications Optional INFO String Optional The format for SCON Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0200 | Length =8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0203 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / ... / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0206 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | reserved | Concerned DPC | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0205 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Cong. Level | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the Network Appearance, Affected Destinations, and INFO String parameters is the same as for the DUNA message (See Section 3.4.1). Sidebottom et al [Page 39] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The Affected Destinations parameter can be used to indicate congestion of multiple destinations or ranges of destinations. However, an SCON message MUST not be delayed to "collect" individual congested destinations into a single SCON message as any delay might affect the timing of congestion indications to the M3UA Users. One use for including a range of Congested DPCs is when the SG supports an ANSI cluster route set to the SS7 network that becomes congested due to outgoing link set congestion. Concerned Destination: 32-bits The optional Concerned Destination parameter is only used if the SCON message is sent from an ASP to the SGP. It contains the point code of the originator of the message that triggered the SCON message. The Concerned Destination parameter contains one Concerned Destination Point Code field, a three-octet parameter to allow for 14-, 16- and 24-bit binary formatted SS7 Point Codes. A Concerned Point Code that is less than 24-bits is padded on the left to the 24-bit boundary. Any resulting Transfer Controlled (TFC) message from the SG is sent to the Concerned Point Code using the single Affected DPC contained in the SCON message to populate the (affected) Destination field of the TFC message Congested Indications: 32-bits The optional Congestion Indications parameter contains a Congestion Level field. This optional parameter is used to communicate congestion levels in national MTP networks with multiple congestion thresholds, such as in ANSI MTP3. For MTP congestion methods without multiple congestion levels (e.g., the ITU international method) the parameter is not included. Congestion Level field: 8-bits (unsigned integer) The Congestion Level field, associated with all of the Affected DPC(s) in the Affected Destinations parameter, contains one of the Following values: 0 No Congestion or Undefined 1 Congestion Level 1 2 Congestion Level 2 3 Congestion Level 3 The congestion levels are defined in the congestion method in the appropriate national MTP recommendations [14,15]. 3.4.5 Destination User Part Unavailable (DUPU) The DUPU message is used by an SGP to inform an ASP that a remote peer MTP3-User Part (e.g., ISUP or SCCP) at an SS7 node is unavailable. Sidebottom et al [Page 40] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The DUPU message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory User/Cause Mandatory INFO String Optional The format for DUPU message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0200 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0203 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Affected DPC | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0204 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Cause | User | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ User/Cause: 32-bits The Unavailability Cause and MTP3-User Identity fields, associated with the Affected DPC in the Affected Destinations parameter, are encoded as follows: Unavailability Cause field: 16-bits (unsigned integer) The Unavailability Cause parameter provides the reason for the unavailability of the MTP3-User. The valid values for the Unavailability Cause parameter are shown in the following table. The values agree with those provided in the SS7 MTP3 User Part Unavailable message. Depending on the MTP3 protocol used in the Network Appearance, additional values may be used - the specification of the relevant MTP3 protocol variant/version recommendation is definitive. 0 Unknown 1 Unequipped Remote User 2 Inaccessible Remote User Sidebottom et al [Page 41] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 MTP3-User Identity field: 16-bits (unsigned integer) The MTP3-User Identity describes the specific MTP3-User that is unavailable (e.g., ISUP, SCCP, ...). Some of the valid values for the MTP3-User Identity are shown below. The values align with those provided in the SS7 MTP3 User Part Unavailable message and Service Indicator. Depending on the MTP3 protocol variant/version used in the network appearance, additional values may be used. The relevant MTP3 protocol variant/version recommendation is definitive. 0 to 2 Reserved 3 SCCP 4 TUP 5 ISUP 6 to 8 Reserved 9 Broadband ISUP 10 Satellite ISUP 11 Reserved 12 AAL type 2 Signalling 13 Bearer Independent Call Control (BICC) 14 Gateway Control Protocol 15 Reserved The format and description of the Affected Destinations parameter is the same as for the DUNA message (See Section 3.4.1.) except that the Mask field is not used and only a single Affected DPC is included. Ranges and lists of Affected DPCs cannot be signalled in a DUPU message, but this is consistent with UPU operation in the SS7 network. The Affected Destinations parameter in an MTP3 User Part Unavailable message (UPU) received by an SGP from the SS7 network contains only one destination. The format and description of the Network Appearance and INFO String parameters is the same as for the DUNA message (See Section 3.4.1). 3.4.6 Destination Restricted (DRST) The DRST message is optionally sent from the SGP to all concerned ASPs to indicate that the SG has determined that one or more SS7 destinations are now restricted from the point of view of the SGP, or in response to a DAUD message if appropriate. The M3UA layer at the ASP is expected to send traffic to the affected destination via an alternate SGP of equal priority, but only if such an alternate route exists and is available. If the affected destination is currently considered unavailable by the ASP, The MTP3-User should be informed that traffic to the affected destination can be resumed. In this case, the M3UA layer should route the traffic through the SGP initiating the DRST message. Sidebottom et al [Page 42] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 This message is optional for the SGP to send and it is optional for the ASP to act on any information received in the message. It is for use in the "STP" case described in Section 1.4.1. The DRST message contains the following parameters: Network Appearance Optional Affected Destinations Mandatory INFO String Optional The format and description of the Network Appearance, Affected Destinations and INFO String parameters is the same as for the DUNA message (See Section 3.4.1). 3.5 ASP State Maintenance (ASPSM) Messages 3.5.1 ASP Up The ASP Up message is used to indicate to a remote M3UA peer that the adaptation layer is ready to receive any SSNM or ASPSM/ASPTM messages for all Routing Keys that the ASP is configured to serve. The ASP Up message contains the following parameters: ASP Identifier Optional INFO String Optional The format for ASP Up message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000e | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASP Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The optional ASP Identifier parameter contains a unique value that is locally significant among the ASPs that support an AS. The SGP should save the ASP Identifier to be used, if necessary, with the Notify message (see Section 3.8.2). The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). 3.5.2 ASP Up Acknowledgement (ASP Up Ack) The ASP UP Ack message is used to acknowledge an ASP Up message received from a remote M3UA peer. Sidebottom et al [Page 43] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The ASP Up Ack message contains the following parameters: INFO String (optional) The format for ASP Up Ack message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). The INFO String in an ASP Up Ack message is independent from the INFO String in the ASP Up message (i.e., it does not have to echo back the INFO String received). 3.5.3 ASP Down The ASP Down message is used to indicate to a remote M3UA peer that the adaptation layer is NOT ready to receive DATA, SSNM, RKM or ASPTM messages. The ASP Down message contains the following parameters: INFO String Optional The format for the ASP Down message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 44] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). 3.5.4 ASP Down Acknowledgement (ASP Down Ack) The ASP Down Ack message is used to acknowledge an ASP Down message received from a remote M3UA peer. The ASP Down Ack message contains the following parameters: Reason Mandatory INFO String Optional The format for the ASP Down Ack message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). The INFO String in an ASP Down Ack message is independent from the INFO String in the ASP Down message (i.e., it does not have to echo back the INFO String received). Sidebottom et al [Page 45] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 3.5.5 Heartbeat (BEAT) The BEAT message is optionally used to ensure that the M3UA peers are still available to each other. It is recommended for use when the M3UA runs over a transport layer other than the SCTP, which has its own heartbeat. The BEAT message contains the following parameters: Heatbeat Data Optional The format for the BEAT message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0009 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Heartbeat Data / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Heartbeat Data parameter contents are defined by the sending node. The Heartbeat Data could include, for example, a Heartbeat Sequence Number and/or Timestamp. The receiver of a BEAT message does not process this field as it is only of significance to the sender. The receiver MUST respond with a BEAT Ack message. 3.5.6 Heartbeat Acknowledgement (BEAT Ack) The BEAT Ack message is sent in response to a received BEAT message. It includes all the parameters of the received BEAT message, without any change. 3.6 Routing Key Management (RKM) Messages 3.6.1 Registration Request (REG REQ) The REG REQ message is sent by an ASP to indicate to a remote M3UA peer that it wishes to register one or more given Routing Keys with the remote peer. Typically, an ASP would send this message to an SGP, and expects to receive a REG RSP message in return with an associated Routing Context value. The REG REQ message contains the following parameters: Routing Key Mandatory Sidebottom et al [Page 46] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 One or more Routing Key parameters MAY be included. The format for the REG REQ message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0207 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Key 1 / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / ... / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0207 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Key n / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Routing Key: variable length The Routing Key parameter is mandatory. The sender of this message expects that the receiver of this message will create a Routing Key entry and assign a unique Routing Context value to it, if the Routing Key entry does not already exist. The Routing Key parameter may be present multiple times in the same message. This is used to allow the registration of multiple Routing Keys in a single message. Sidebottom et al [Page 47] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format of the Routing Key parameter is as follows. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local-RK-Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic Mode Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Point Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SI (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SSN (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Origination Point Code List (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Circuit Range List (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Local-RK-Identifier: 32-bit integer The mandatory Local-RK-Identifier field is used to uniquely identify the registration request. The Identifier value is assigned by the ASP, and is used to correlate the response in an REG RSP message with the original registration request. The Identifier value must remain unique until the REG RSP message is received. The format of the Local-RK-Identifier field is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020a | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local-RK-Identifier value | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Traffic Mode Type: 32-bit (unsigned integer) The Traffic Mode Type parameter is mandatory and identifies the traffic mode of operation of the ASP(s) within an Application Server. The valid values for Traffic Mode Type are shown in the following table: 1 Over-ride 2 Load-share 3 Broadcast Sidebottom et al [Page 48] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 If the receiver of the REG REQ creates a new Routing Key entry, then the Traffic Mode Type sets the traffic mode for the new Application Server. If the receiver of the REG REQ determines that a matching Routing Key already exists, the Traffic Mode Type MUST match the existing traffic mode for the AS. Destination Point Code: The Destination Point Code parameter is mandatory, and identifies the Destination Point Code of incoming SS7 traffic for which the ASP is registering. The format is the same as described for the Affected Destination parameter in the DUNA message (See Section 3.4.1). Its format is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020b | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Destination Point Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Network Appearance: The optional Network Appearance parameter field identifies the SS7 network context for the Routing Key, and has the same format as in the DATA message (See Section 3.3.1). The absence of the Network Appearance parameter in the Routing Key indicates the use of any Network Appearance value, Its format is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0200 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Service Indicators (SI): n X 8-bit integers The optional SI field contains one or more Service Indicators from the values as described in the MTP3-User Identity field of the DUPU message. The absence of the SI parameter in the Routing Key indicates the use of any SI value, excluding of course MTP management. Where an SI parameter does not contain a multiple of four SIs, the parameter is padded out to 32-byte alignment. An SI value of zero is not valid in M3UA. The SI format is: Sidebottom et al [Page 49] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020c | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SI #1 | SI #2 | SI #3 | SI #4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / ... / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SI #n | 0 Padding, if necessary | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Subsystem Numbers (SSN): n X 8-bit integers The optional SSN field contains one or more SCCP subsystem numbers, and is used in conjunction with an SI values of 3 (i.e., SCCP) only. The absence of the SSN parameter in the Routing Key indicates the use of any SSN value, in the case of SCCP traffic. Where an SSN parameter does not contain a multiple of four SSNs, the parameter is padded out to 32-byte alignment. The subsystem number values associated are defined by the local network operator, and typically follow ITU-T Recommendation Q.713 [5]. An SSN value of zero is not valid in M3UA. The format of this field is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020d | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SSN #1 | SSN #2 | SSN #3 | SSN #4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / ... / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SSN #n | 0 Padding, if necessary | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ OPC List: The Originating Point Code List parameter contains one or more SS7 OPC entries, and its format is the same as the Destination Point Code parameter. The absence of the OPC List parameter in the Routing Key indicates the use of any OPC value, Sidebottom et al [Page 50] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020e | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / ... / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Circuit Range: An ISUP controlled circuit is uniquely identified by the SS7 OPC, DPC and CIC value. For the purposes of identifying Circuit Ranges in an M3UA Routing Key, the optional Circuit Range parameter includes one or more circuit ranges, each identified by an OPC and Upper/Lower CIC value. The DPC is implicit as it is mandatory and already included in the DPC parameter of the Routing Key. The absence of the Circuit Range parameter in the Routing Key indicates the use of any Circuit Range values, in the case of ISUP/TUP traffic. The Origination Point Code is encoded the same as the Destination Point Code parameter, while the CIC values are 16-bit integers. The Circuit Range format is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x020f | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Lower CIC Value #1 | Upper CIC Value #1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Lower CIC Value #2 | Upper CIC Value #2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / ... / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask = 0 | Origination Point Code #n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Lower CIC Value #n | Upper CIC Value #n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 51] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 3.6 2 Registration Response (REG RSP) The REG RSP message is used as a response to the REG REQ message from a remote M3UA peer. It contains indications of success/failure for registration requests and returns a unique Routing Context value for successful registration requests, to be used in subsequent M3UA Traffic Management protocol. The REG RSP message contains the following parameters: Registration Result Mandatory One or more Registration Result parameters MAY be included. The format for the REG RSP message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0208 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Registration Result 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / ... / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0208 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Registration Result n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Registration Results: The Registration Result parameter contains the registration status for a single Routing Key in an REG REQ message. The number of results in a single REG RSP message MAY be anywhere from one to the total number of number of Routing Key parameters found in the corresponding REG REQ message. Where multiple REG RSP messages are used in reply to REG REQ message, a specific result SHOULD be in only one REG RSP message. The format of each result is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local-RK-Identifier value | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Registration Status | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Routing Context | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Local-RK-Identifier: 32-bit integer The Local-RK-Identifier contains the same value as found in the matching Routing Key parameter found in the REG REQ message (See Section 3.5.5.1). Sidebottom et al [Page 52] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Registration Status: 32-bit integer The Registration Result Status field indicates the success or the reason for failure of a registration request. Its values may be: 0 Successfully Registered 1 Error - Unknown 2 Error - Invalid DPC 3 Error - Invalid Network Appearance 4 Error - Invalid Routing Key 5 Error - Permission Denied 6 Error - Cannot Support Unique Routing 7 Error - Routing Key not Currently Provisioned 8 Error - Insufficient Resources 9 Error - Unsupported RK parameter Field 10 Error - Unsupported/Invalid Traffic Handling Mode Routing Context: 32-bit integer The Routing Context field contains the Routing Context value for the associated Routing Key if the registration was successful. It is set to "0" if the registration was not successful. 3.6.3 De-Registration Request (DEREG REQ) The DEREG REQ message is sent by an ASP to indicate to a remote M3UA peer that it wishes to de-register a given Routing Key. Typically, an ASP would send this message to an SGP, and expects to receive a DEREG RSP message in return with the associated Routing Context value. The DEREG REQ message contains the following parameters: Routing Context Mandatory The format for the DEREG REQ message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 53] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Routing Context: n X 32-bit integers The Routing Context parameter contains (a list of) integers indexing the Application Server traffic that the sending ASP is currently registered to receive from the SGP but now wishes to deregister. 3.6.4 De-Registration Response (DEREG RSP) The DEREG RSP message is used as a response to the DEREG REQ message from a remote M3UA peer. The DEREG RSP message contains the following parameters: De-registration Result Mandatory One or more De-registration Result parameters MAY be included. The format for the DEREG RSP message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0209 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | De-Registration Result 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / ... / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0209 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | De-Registration Result n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ De-Registration Results: The De-Registration Result parameter contains the de-registration status for a single Routing Context in a DEREG REQ message. The number of results in a single DEREG RSP message MAY be anywhere from one to the total number of number of Routing Context values found in the corresponding REG REQ message. Where multiple DEREG RSP messages are used in reply to DEREG REQ message, a specific result SHOULD be in only one DEREG RSP message. The format of each result is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Routing Context | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | De-Registration Status | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 54] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Routing Context: 32-bit integer The Routing Context field contains the Routing Context value of the matching Routing Key to deregister, as found in the DEREG REQ message. De-Registration Status: 32-bit integer The De-Registration Result Status field indicates the success or the reason for failure of the de-registration. Its values may be: 0 Successfully De-registered 1 Error - Unknown 2 Error - Invalid Routing Context 3 Error - Permission Denied 4 Error - Not Registered 5 Error - ASP Currently Active for Routing Context 3.7 ASP Traffic Maintenance (ASPTM) Messages 3.7.1 ASP Active The ASP Active message is sent by an ASP to indicate to a remote M3UA peer that it is ready to process signalling traffic for a particular Application Server. The ASP Active message affects only the ASP state for the Routing Keys identified by the Routing Contexts, if present. The ASP Active message contains the following parameters: Traffic Mode Type Mandatory Routing Context Optional INFO String Optional Sidebottom et al [Page 55] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format for the ASP Active message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000b | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic Mode Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Traffic Mode Type: 32-bit (unsigned integer) The Traffic Mode Type parameter identifies the traffic mode of operation of the ASP within an AS. The valid values for Traffic Mode Type are shown in the following table: 1 Over-ride 2 Load-share 3 Broadcast 5 Over-ride (Standby) 6 Load-share (Standby) 7 Broadcst (Standby) Within a particular Routing Context, Over-ride,Load-share and Broadcast, either active or standby, MUST NOT be mixed. The Over- ride value indicates that the ASP is operating in Over-ride mode, and the ASP takes over all traffic in an Application Server (i.e., primary/back-up operation), over-riding any currently active ASPs in the AS. In Load-share mode, the ASP will share in the traffic distribution with any other currently active ASPs. In Broadcast mode, the ASP will receive the same messages as any other currently active ASP. The Standby versions of the Over-ride, Load-share and Broadcast Types indicate that the ASP is declaring itself ready to accept traffic but leaves it up to the sender as to when the traffic is started. Over-ride (Standby) indicates that the traffic sender continues to use the currently active ASP until it can no longer send/receive traffic (i.e., the currently active ASP transitions to state ASP-DOWN or ASP-INACTIVE). At this point the sender MUST move the standby ASP to the ASP-ACTIVE state and commence traffic. Load- share (Standby) and Broadcast (Standby) are similar - the sender continues to load-share or broadcast to the current ASPs until it is determined Sidebottom et al [Page 56] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 that there is insufficient resources in the Load-share or Broadcast group. When there are insufficient ASPs, the sender MUST move the ASP to state ASP-ACTIVE. Routing Context: n X 32-bit integers The optional Routing Context parameter contains (a list of) integers indexing the Application Server traffic that the sending ASP is configured/registered to receive. There is one-to-one relationship between an index entry and an SGP Routing Key or AS Name. Because an AS can only appear in one Network Appearance, the Network Appearance parameter is not required in the ASP Active message. An Application Server Process may be configured to process traffic for more than one logical Application Server. From the perspective of an ASP, a Routing Context defines a range of signalling traffic that the ASP is currently configured to receive from the SGP. For example, an ASP could be configured to support call processing for multiple ranges of PSTN trunks and therefore receive related signalling traffic, identified by separate SS7 DPC/OPC/CIC ranges. The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). 3.7.2 ASP Active Acknowledgement (ASP Active Ack) The ASP Active Ack message is used to acknowledge an ASP Active message received from a remote M3UA peer. In the case where an ASP Active (Over-ride (standby)), ASP Active (Load-share (standby)) or ASP Active (Broadcast (standby)) message is received, a second ASP Active Ack message is sent when the ASP is moved from the ASP-STANDBY to the ASP-ACTIVE state. The ASP Active Ack message contains the following parameters: Traffic Mode Type Mandatory Routing Context Optional INFO String Optional Sidebottom et al [Page 57] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format for the ASP Active Ack message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000b | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic Mode Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1). The INFO String in an ASP Active Ack message is independent from the INFO String in the ASP Active message (i.e., it does not have to echo back the INFO String received). The format of the Traffic Mode Type and Routing Context parameters is the same as for the ASP Active message. (See Section 3.5.5). 3.7.3 ASP Inactive The ASP Inactive message is sent by an ASP to indicate to a remote M3UA peer that it is no longer an active ASP to be used from within a list of ASPs. The ASP Inactive message affects only the ASP state in the Routing Keys identified by the Routing Contexts, if present. The ASP Inactive message contains the following parameters: Routing Context Optional INFO String Optional Sidebottom et al [Page 58] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format for the ASP Inactive message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional Routing Context and INFO String parameters is the same as for the ASP Active message (See Section 3.5.5.) 3.7.4 ASP Inactive Acknowledgement (ASP Inactive Ack) The ASP Inactive Ack message is used to acknowledge an ASP Inactive message received from a remote M3UA peer. The ASP Inactive Ack message contains the following parameters: Routing Context Optional INFO String Optional The format for the ASP Inactive Ack message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 59] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format and description of the optional INFO String parameter is the same as for the DUNA message (See Section 3.4.1.) The INFO String in an ASP Inactive Ack message is independent from the INFO String in the ASP Inactive message (i.e., it does not have to echo back the INFO String received). The format of the Routing Context parameter is the same as for the ASP Inactive message. (See Section 3.5.7). 3.8 Management (MGMT) Messages 3.8.1 Error The Error message is used to notify a peer of an error event associated with an incoming message. For example, the message type might be unexpected given the current state, or a parameter value might be invalid. The Error message contains the following parameters: Error Code Mandatory Diagnostic Information Optional The format for the Error message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000c | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Error Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0007 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Diagnostic Information / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Error Code: 32-bits (unsigned integer) The Error Code parameter indicates the reason for the Error Message. The Error parameter value can be one of the following values: 1 Invalid Version 2 Invalid Network Appearance 3 Unsupported Message Class Sidebottom et al [Page 60] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 4 Unsupported Message Type 5 Unsupported/Invalid Traffic Handling Mode 6 Unexpected Message 7 Protocol Error 8 Invalid Routing Context 9 Invalid Stream Identifier 10 Invalid Parameter Value 11 Refused - Management Blocking 12 Unknown Routing Context 13 Missing, Duplicated or Invalid ASP Identifier The "Invalid Version" error is sent if a message was received with an invalid or unsupported version. The Error message contains the supported version in the Common header. The Error message could optionally provide the supported version in the Diagnostic Information area. The "Invalid Network Appearance" error is sent by a SGP if an ASP sends a message with an invalid (unconfigured) Network Appearance value. The "Unsupported Message Class" error is sent if a message with an unexpected or unsupported Message Class is received. The "Unsupported Message Type" error is sent if a message with an unexpected or unsupported Message Type is received. The "Unsupported/Invalid Traffic Handling Mode" error is sent by a SGP if an ASP sends an ASP Active message with an unsupported Traffic Mode Type or a Traffic Mode Type that is inconsistent with the presently configured mode for the Application Server. An example would be a case in which the SGP did not support load-sharing. The "Unexpected Message" error MAY be sent if a defined and recognized message is received that is not expected in the current state (in some cases the ASP may optionally silently discard the message and not send an Error message). For example, silent discard is used by an ASP if it received a DATA message from an SGP while it was in the ASP-INACTIVE state. The "Protocol Error" error is sent for any protocol anomaly(i.e., reception of a parameter that is syntactically correct but unexpected in the current situation. The "Invalid Routing Context" error is sent if a message is received from a peer with an invalid (unconfigured) Routing Context value. The "Invalid Stream Identifier" error is sent if a message is received on an unexpected SCTP stream (e.g., a Management message was received on a stream other than "0"). Sidebottom et al [Page 61] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The " Invalid Parameter Value " error is sent if a message is received with an invalid parameter value (e.g., a DUPU message was received with a Mask value other than "0"). The "Refused - Management Blocking" error is sent when an ASP-Up or ASP-Active message is received and the request is refused for management reasons (e.g., management lock-out"). The "Unknown Routing Context" Error is sent if a message is received from a peer without a Routing Context parameter and it is not known by configuration data which Application Servers are referenced. The "Refused - Missing, Duplicated or Invalid ASP Identifier" error is sent when an ASP-Up message is received and the request is refused because an ASP ID is required, or the value is invalid/duplicated. Diagnostic Information: variable length When included, the optional Diagnostic information can be any information germane to the error condition, to assist in identification of the error condition. In the case of an Invalid Network Appearance, Traffic Handling Mode, Routing Context or Parameter Value, the Diagnostic information parameter MUST be added and include the offending parameter. In the other cases, the Diagnostic information MAY be the first 40 bytes of the offending message. Error messages MUST NOT be generated in response to other Error messages. 3.8.2 Notify The Notify message used to provide an autonomous indication of M3UA events to an M3UA peer. The Notify message contains the following parameters: Status Mandatory ASP Identifier Optional Routing Context Optional INFO String Optional Sidebottom et al [Page 62] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The format for the Notify message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000d | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Status Type | Status Information | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x000e | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ASP Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0006 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Routing Context / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 0x0004 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / INFO String / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Status Type: 16-bits (unsigned integer) The Status Type parameter identifies the type of the Notify message. The following are the valid Status Type values: 1 Application Server State Change (AS-State_Change) 2 Other Status Information: 16-bits (unsigned integer) The Status Information parameter contains more detailed information for the notification, based on the value of the Status Type. If the Status Type is AS-State_Change the following Status Information values are used: 1 reserved 2 Application Server Inactive (AS-INACTIVE) 3 Application Server Active (AS-ACTIVE) 4 Application Server Pending (AS-PENDING) These notifications are sent from an SGP to an ASP upon a change in status of a particular Application Server. The value reflects the new state of the Application Server. Sidebottom et al [Page 63] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 If the Status Type is Other, then the following Status Information values are defined: 1 Insufficient ASP Resources Active in AS 2 Alternate ASP Active These notifications are not based on the SGP reporting the state change of an ASP or AS. In the Insufficent ASP Resources case, the SGP is indicating to an ASP_INACTIVE ASP in the AS that another ASP is required to handle the load of the AS (Load-sharing or Broadcast mode). For the Alternate ASP Active case, an ASP is informed when an alternate ASP transitions to the ASP-ACTIVE state in Over-ride mode. The format and description of the optional ASP Identifier, Routing Context and Info String parameters is the same as for the ASP Active message (See Section 3.5.5.) 4. Procedures The M3UA layer needs to respond to various local primitives it receives from other layers as well as the messages that it receives from the peer M3UA layer. This section describes the M3UA procedures in response to these events. 4.1 Procedures to Support the M3UA-User and Layer Management Layers 4.1.1 Receipt of Primitives from the M3UA-User On receiving an MTP-TRANSFER request primitive from an upper layer at an ASP/IPSP, or the nodal inter-working function at an SGP, the M3UA layer sends a corresponding DATA message (see Section 3) to its M3UA peer. The M3UA peer receiving the DATA message sends an MTP-TRANSFER indication primitive to the upper layer. The M3UA message distribution function (see Section 1.4.2.1) determines the Application Server (AS) based on comparing the information in the MTP-TRANSFER request primitive with a provisioned Routing Key. >From the list of ASPs within the AS table, an ASP in the ASP-ACTIVE state is selected and a DATA message is constructed and issued on the corresponding SCTP association. If more than one ASP is in the ASP- ACTIVE state (i.e., traffic is to be load-shared across more than one ASP), one of the ASPs in the ASP_ACTIVE state is selected from the list. If the ASPs are in Broadcast Mode, all active ASPs will be selected and the message sent to each of the active ASPs. The selection algorithm is implementation dependent but could, for example, be round-robin or based on, for example, the SLS or ISUP CIC. The appropriate selection algorithm must be chosen carefully as it is dependent on application assumptions and understanding of the degree of state coordination between the ASP_ACTIVE ASPs in the AS. Sidebottom et al [Page 64] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 In addition, the message needs to be sent on the appropriate SCTP stream, again taking care to meet the message sequencing needs of the signalling application. When there is no Routing Key match, or only a partial match, for an incoming SS7 message, a default treatment MUST be specified. Possible solutions are to provide a default Application Server at the SGP that directs all unallocated traffic to a (set of) default ASP(s), or to drop the message and provide a notification to Layer Management in an M-ERROR indication primitive. The treatment of unallocated traffic is implementation dependent. 4.1.2 Receipt of Primitives from the Layer Management On receiving primitives from the local Layer Management, the M3UA layer will take the requested action and provide an appropriate response primitive to Layer Management. An M-SCTP_ESTABLISH request primitive from Layer Management at an ASP or IPSP will initiate the establishment of an SCTP association. The M3UA layer will attempt to establish an SCTP association with the remote M3UA peer by sending an SCTP-ASSOCIATE primitive to the local SCTP layer. When an SCTP association has been successfully established, the SCTP will send an SCTP-COMMUNICATION_UP notification primitive to the local M3UA layer. At the SGP or IPSP that initiated the request, the M3UA layer will send an M-SCTP_ESTABLISH confirm primitive to Layer Management when the association set-up is complete. At the peer M3UA layer, an M-SCTP_ESTABLISH indication primitive is sent to Layer Management upon successful completion of an incoming SCTP association set-up. An M-SCTP_RELEASE request primitive from Layer Management initates the tear-down of an SCTP association. The M3UA layer accomplishes a graceful shutdown of the SCTP association by sending an SCTP-SHUTDOWN primitive to the SCTP layer. When the graceful shutdown of the SCTP association has been accomplished, the SCTP layer returns an SCTP-SHUTDOWN_COMPLETE notification primitive to the local M3UA layer. At the M3UA Layer that initiated the request, the M3UA layer will send an M-SCTP_RELEASE confirm primitive to Layer Management when the association teardown is complete. At the peer M3UA Layer, an M-SCTP_RELEASE indication primitive is sent to Layer Management upon successful tear-down of an SCTP association. An M-SCTP_STATUS request primitive supports a Layer Management query of the local status of a particular SCTP association. The M3UA layer simply maps the M-SCTP_STATUS request primitive to an SCTP-STATUS Sidebottom et al [Page 65] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 primitive to the SCTP layer. When the SCTP responds, the M3UA layer maps the association status information to an M-SCTP_STATUS confirm primitive. No peer protocol is invoked. Similar LM-to-M3UA-to-SCTP and/or SCTP-to-M3UA-to-LM primitive mappings can be described for the various other SCTP Upper Layer primitives in RFC2960 [13] such as INITIALIZE, SET PRIMARY, CHANGE HEARTBEAT, REQUEST HEARTBEAT, GET SRTT REPORT, SET FAILURE THRESHOLD, SET PROTOCOL PARAMETERS, DESTROY SCTP INSTANCE, SEND FAILURE, AND NETWORK STATUS CHANGE. Alternatively, these SCTP Upper Layer primitives (and Status as well) can be considered for modeling purposes as a Layer Management interaction directly with the SCTP Layer. M-NOTIFY indication and M-ERROR indication primitives indicate to Layer Management the notification or error information contained in a received M3UA Notify or Error message respectively. These indications can also be generated based on local M3UA events. An M-ASP_STATUS request primitive supports a Layer Management query of the status of a particular local or remote ASP. The M3UA layer responds with the status in an M-ASP_STATUS confirm primitive. No M3UA peer protocol is invoked. An M-AS_STATUS request supports a Layer Management query of the status of a particular AS. The M3UA responds with an M-AS_STATUS confirm primitive. No M3UA peer protocol is invoked. M-ASP_UP request, M-ASP_DOWN request, M-ASP_ACTIVE request and M-ASP_ INACTIVE request primitives allow Layer Management at an ASP to initiate state changes. Upon successful completion, a corresponding confirm primitive is provided by the M3UA layer to Layer Management. If an invocation is unsuccessful, an Error indication primitive is provided in the primitive. These requests result in outgoing ASP Up, ASP Down, ASP Active and ASP Inactive messages to the remote M3UA peer at an SGP or IPSP. 4.1.3 Receipt of M3UA Peer Management Messages Upon successful state changes resulting from reception of ASP Up, ASP Down, ASP Active and ASP Inactive messages from a peer M3UA, the M3UA layer SHOULD invoke corresponding M-ASP_UP, M-ASP_DOWN, M- ASP_ACTIVE and M-ASP_INACTIVE, M-AS_ACTIVE, M-AS_INACTIVE, and M- AS_DOWN indication primitives to the local Layer Management. M-NOTIFY indication and M-ERROR indication primitives indicate to Layer Management the notification or error information contained in a received M3UA Notify or Error message. These indications can also be generated based on local M3UA events. Sidebottom et al [Page 66] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 4.2 Procedures to Support the Management of SCTP Associations with M3UA Peers These procedures support the M3UA management of SCTP Associations between SGPs and ASPs or between IPSPs. 4.2.1 AS and ASP State Maintenance The M3UA layer on the SGP maintains the state of each remote ASP, in each Application Server that the ASP is configured to receive traffic, as input to the M3UA message distribution function. Similarly, where IPSPs use M3UA in a point-to-point fashion, the M3UA layer in an IPSP maintains the state of remote IPSPs. For the purposes of the following procedures, only the SGP/ASP case is described but the SGP side of the procedures also apply to an IPSP sending traffic to an AS consisting of a set of remote IPSPs. 4.2.1.1 ASP States The state of each remote ASP, in each AS that it is configured to operate, is maintained in the M3UA layer in the SGP. The state of a particular ASP in a particular AS changes due to events. The events include: * Reception of messages from the peer M3UA layer at the ASP; * Reception of some messages from the peer M3UA layer at other ASPs in the AS (e.g., ASP Active message indicating "Over-ride"); * Reception of indications from the SCTP layer; or * Local Management intervention. The ASP state transition diagram is shown in Figure 4. The possible states of an ASP are: ASP-DOWN: The remote M3UA peer at the ASP is unavailable and/or the related SCTP association is down. Initially all ASPs will be in this state. An ASP in this state SHOULD NOT be sent any M3UA messages. ASP-INACTIVE: The remote M3UA peer at the ASP is available (and the related SCTP association is up) but application traffic is stopped. In this state the ASP MAY be sent any non-DATA M3UA messages. ASP-ACTIVE: The remote M3UA peer at the ASP is available and application traffic is active (for a particular Routing Context or set of Routing Contexts). ASP-STANDBY: The remote M3UA peer at the ASP is available and ready to receive application traffic at any time (for a particular Routing Context or set of Routing Contexts). In this state the ASP MAY be sent any non-Data M3UA messages. Sidebottom et al [Page 67] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Figure 4: ASP State Transition Diagram +--------------+ | ASP-ACTIVE | +----------------------| or | | Other +-------| ASP-STANDBY* | | ASP in AS | +--------------+ | Overrides | ^ | | | ASP | | ASP | | Active | | Inactive | | | v | | +--------------+ | | | | | +------>| ASP-INACTIVE | | +--------------+ | ^ | ASP Down/ | ASP | | ASP Down / SCTP CDI/ | Up | | SCTP CDI/ SCTP RI | | v SCTP RI | +--------------+ | | | +--------------------->| ASP-DOWN | | | +--------------+ *Note: ASP-ACTIVE and ASP-STANDBY differ only in whether the ASP is currently receiving Data traffic within the AS. SCTP CDI: The SCTP CDI denotes the local SCTP layer's Communication Down Indication to the Upper Layer Protocol (M3UA) on an SGP. The local SCTP layer will send this indication when it detects the loss of connectivity to the ASP's peer SCTP layer. SCTP CDI is understood as either a SHUTDOWN_COMPLETE notification or COMMUNICATION_LOST notification from the SCTP layer. SCTP RI: The local SCTP layer's Restart indication to the upper layer protocol (M3UA) on an SG. The local SCTP will send this indication when it detects a restart from the ASP's peer SCTP layer. 4.2.1.2 AS States The state of the AS is maintained in the M3UA layer on the SGP. The state of an AS changes due to events. These events include: * ASP state transitions * Recovery timer triggers The possible states of an AS are: AS-DOWN: The Application Server is unavailable. This state implies that all related ASPs are in the ASP-DOWN state for this AS. Initially the AS will be in this state. An Application Server MUST be in the AS- DOWN state before it can be removed from a configuration. Sidebottom et al [Page 68] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 AS-INACTIVE: The Application Server is available but no application traffic is active (i.e., one or more related ASPs are in the ASP- INACTIVE state, but none in the ASP-ACTIVE or ASP-STANDBY states). The recovery timer T(r) is not running or has expired. AS-ACTIVE: The Application Server is available and application traffic is active. This state implies that at least one ASP is in the ASP- ACTIVE state. AS-PENDING: An active ASP has transitioned to ASP-INACTIVE or ASP-DOWN and it was the last remaining active ASP in the AS (and no ASPs in the ASP-STANDBY state are available. A recovery timer T(r) SHOULD be started and all incoming signalling messages SHOULD be queued by the SGP. If an ASP becomes ASP-ACTIVE before T(r) expires, the AS is moved to the AS-ACTIVE state and all the queued messages will be sent to the ASP. If T(r) expires before an ASP becomes ASP-ACTIVE, the SGP stops queuing messages and discards all previously queued messages. The AS will move to the AS-INACTIVE state if at least one ASP is in ASP-INACTIVE state, otherwise it will move to AS-DOWN state. Figure 5 shows an example AS state machine for the case where the AS/ASP data is pre-configured. For other cases where the AS/ASP configuration data is created dynamically, there would be differences in the state machine, especially at creation of the AS. For example, where the AS/ASP configuration data is not created until Registration of the first ASP, the AS-INACTIVE state is entered directly upon the first successful REG REQ from an ASP. Another example is where the AS/ASP configuration data is not created until the first ASP successfully enters the ASP-ACTIVE state. In this case the AS-ACTIVE state is entered directly. Sidebottom et al [Page 69] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Figure 5: AS State Transition Diagram +----------+ one ASP trans to ACTIVE +-------------+ | AS- |---------------------------->| AS- | | INACTIVE | | ACTIVE | | |<--- | | +----------+ \ +-------------+ ^ | \ Tr Expiry, ^ | | | \ at least one | | | | \ ASP in ASP-INACTIVE | | | | \ | | | | \ | | | | \ | | one ASP | | all ASP \ one ASP | | Last ACTIVE trans | | trans to \ trans to | | ASP trans to to | | ASP-DOWN -------\ ASP- | | ASP-INACTIVE ASP- | | \ ACTIVE | | or ASP-DOWN INACTIVE| | \ | | | | \ | | | | \ | | | v \ | v +----------+ \ +-------------+ | | --| | | AS-DOWN | | AS-PENDING | | | | (queueing) | | |<----------------------------| | +----------+ Tr Expiry (no ASP +-------------+ in ASP-INACTIVE state) Tr = Recovery Timer 4.2.2 M3UA Management Procedures for Primitives Before the establishment of an SCTP association the ASP state at both the SGP and ASP is assumed to be in the state ASP-DOWN. Once the SCTP association is established (see Section 4.1.2) and assuming that the local M3UA-User is ready, the local M3UA ASP Maintenance (ASPM) function will initiate the relevant procedures, using the ASP Up/ASP Down/ASP Active/ASP Inactive messages to convey the ASP state to the SGP (see Section 4.3.3). If the M3UA layer subsequently receives an SCTP-COMMUNICATION_DOWN or SCTP-RESTART indication primitive from the underlying SCTP layer, it will inform the Layer Management by invoking the M-SCTP_STATUS indication primitive. The state of the ASP will be moved to ASP-DOWN At an ASP, the MTP3-User will be informed of the unavailability of any affected SS7 destinations through the use of MTP-PAUSE indication primitives. In the case Sidebottom et al [Page 70] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 of SS7 network isolation, the local MTP3-Users MAY be informed by implementation-dependent means, as there is currently no primitive defined for conveying this information. In the case of SCTP-COMMUNICATION_DOWN, the SCTP client MAY try to re- establish the SCTP Association. This MAY be done by the M3UA layer automatically, or Layer Management MAY re-establish using the M- SCTP_ESTABLISH request primitive. In the case of an SCTP-RESTART indication at an ASP, the ASP is now considered by its M3UA peer to be in the ASP-DOWN state. The ASP, if it is to recover, must begin any recovery with the ASP-Up procedure. 4.2.3 M3UA Management Procedures for Peer-to-Peer Messages All M3UA Management and ASP State and Traffic Maintenance messages are sent on a sequenced stream to ensure ordering. SCTP stream '0' is used. 4.2.3.1 ASP Up Procedures After an ASP has successfully established an SCTP association to an SGP, the SGP waits for the ASP to send an ASP Up message, indicating that the ASP M3UA peer is available. The ASP is always the initiator of the ASP Up message. This action MAY be initiated at the ASP by an M-ASP_UP request primitive from Layer Management or MAY be initiated automatically by an M3UA management function. When an ASP Up message is received at an SGP and internally the remote ASP is in the ASP-DOWN state and not considered locked-out for local management reasons, the SGP marks the remote ASP in the state ASP- INACTIVE and informs Layer Management with an M-ASP_Up indication primitive. If the SGP is aware, via current configuration data, which Application Servers the ASP is configured to operate in, the SGP updates the ASP state to ASP-INACTIVE in each AS that it is a member. Alternatively, the SGP may move the ASP into a pool of Inactive ASPs available for future configuration within Application Server(s), determined in a subsequent Registration Request or ASP Active procedure. If the ASP Up message contains an ASP Identifier, the SGP should save the ASP Identifier for that ASP. The SGP responds with an ASP Up Ack message in acknowledgement. The SGP sends an ASP Up Ack message in response to a received ASP Up message even if the ASP is already marked as ASP- INACTIVE at the SGP. If for any local reason (e.g., management lock-out) the SGP cannot respond with an ASP Up Ack message, the SGP responds to an ASP Up message with an Error message with Reason "Refused - Management Blocking". At the ASP, the ASP Up Ack message received is not acknowledged. Layer Management is informed with an M-ASP_UP confirm primitive. When an ASP Sidebottom et al [Page 71] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 enters the ASP-Inactive state from the ASP_Down state towards an SGP the M3UA MUST mark all SS7 destinations configured to be reachable via this SGP as available. When the ASP sends an ASP Up message it starts timer T(ack). If the ASP does not receive a response to an ASP Up message within T(ack), the ASP MAY restart T(ack) and resend ASP-Up messages until it receives an ASP Up Ack message. T(ack) is provisionable, with a default of 2 seconds. Alternatively, retransmission of ASP Up messages MAY be put under control of Layer Management. In this method, expiry of T(ack) results in an M-ASP_UP confirm primitive carrying a negative indication. The ASP must wait for the ASP Up Ack message before sending any other M3UA messages (e.g., ASP Active or REG REQ). If the SGP receives any other M3UA messages before an ASP Up message is received, the SGP SHOULD discard them. If an ASP Up message is received and internally the remote ASP is in the ASP-ACTIVE or ASP-STANDBY state, an ASP-Up Ack message is returned, as well as an Error message ("Unexpected Message), and the remote ASP state is changed to ASP-INACTIVE in all relevant Application Servers. If an ASP Up message is received and internally the remote ASP is already in the ASP-INACTIVE state, an ASP Up Ack message is returned and no further action is taken. 4.2.3.1.1 M3UA Version Control If an ASP Up message with an unsupported version is received, the receiving end responds with an Error message, indicating the version the receiving node supports and notifies Layer Management. This is useful when protocol version upgrades are being performed in a network. A node upgraded to a newer version should support the older versions used on other nodes it is communicating with. Because ASPs initiate the ASP Up procedure it is assumed that the Error message would normally come from the SGP. 4.2.3.1.2 IPSP Considerations In the case of peer-to-peer IPSPs, either of the IPSPs (IPSP_A) may start operations by sending an ASP Up message to the remote peer (IPSP_B). When the ASP Up message is received at IPSP_B and internally the remote IPSP_A is in the ASP-DOWN state and not considered locked- out for local management reasons, IPSP_B marks the remote IPSP_A in the state ASP-INACTIVE and informs Layer Management with an M-ASP_Up indication primitive. IPSP_B returns an ASP-Up Ack message to IPSP_A. IPSP_A moves IPSP_B to the ASP-INACTIVE state upon reception of an ASP Up Ack message, if is not already in the ASP_INACTIVE state, and informs Layer Management with an M-ASP_UP confirmation primitive. Sidebottom et al [Page 72] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 If for any local reason (e.g., management lock-out) the IPSP_B cannot respond with an ASP Up Ack message, it responds to an ASP Up message with an Error message with Reason "Refused - Management Blocking" and leaves IPSP_A in the ASP-DOWN state. 4.2.3.2 ASP-Down Procedures The ASP will send an ASP Down message to an SGP when the ASP wishes to be removed from service in all Application Servers that it is a member and no longer receive any DATA, SSNM or ASPTM messages. This action MAY be initiated at the ASP by an M-ASP_DOWN request primitive from Layer Management or MAY be initiated automatically by an M3UA management function. Whether the ASP is permanently removed from any AS is a function of configuration management. In the case where the ASP previously used the Registration procedures (see Section 3.5.5) to register within Application Servers but has not deregistered from all of them prior to sending the ASP Down message, the SGP SHOULD consider the ASP as Deregistered in all Application Servers that it is still a member. The SGP marks the ASP as ASP-DOWN, informs Layer Management with an M- ASP_Down indication primitive, and returns an ASP Down Ack message to the ASP. The SGP sends an ASP Down Ack message in response to a received ASP- Down message from the ASP even if the ASP is already marked as ASP-DOWN at the SGP. The SGP sends an ASP Down Ack message even if the reason in the received ASP Down message is considered invalid. At the ASP, the ASP Down Ack message received is not acknowledged. Layer Management is informed with an M-ASP_DOWN confirm primitive. If the ASP receives an ASP Down Ack without having sent an ASP Down message, the ASP should now consider itself as in the ASP-DOWN state. If the ASP was previously in the ASP-ACTIVE or ASP_INACTIVE state, the ASP should then initiate procedures to return itself to its previous state. When the ASP sends an ASP Down message it starts timer T(ack). If the ASP does not receive a response to an ASP Down message within T(ack), the ASP MAY restart T(ack) and resend ASP Down messages until it receives an ASP Down Ack message. T(ack) is provisionable, with a default of 2 seconds. Alternatively, retransmission of ASP Down messages MAY be put under control of Layer Management. In this method, expiry of T(ack) results in an M-ASP_DOWN confirm primitive carrying a negative indication. Sidebottom et al [Page 73] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 4.2.3.4 ASP-Active Procedures Anytime after the ASP has received an ASP Up Ack message from the SGP or IPSP, the ASP sends an ASP Active message to the SGP indicating that the ASP is ready to start processing traffic. This action MAY be initiated at the ASP by an M-ASP_ACTIVE request primitive from Layer Management or MAY be initiated automatically by an M3UA management function. In the case where an ASP wishes to process the traffic for more than one Application Server across a common SCTP association, the ASP Active message(s) SHOULD contain a list of one or more Routing Contexts to indicate for which Application Servers the ASP Active message applies. It is not necessary for the ASP to include all Routing Contexts of interest in a single ASP Active message, thus requesting to become active in all Routing Contexts at the same time. Multiple ASP Active messages MAY be used to activate within the Application Servers independently, or in sets. In the case where an ASP Active message does not contain a Routing Context parameter, the receiver must know, via configuration data, which Application Server(s) the ASP is a member. For the Application Servers that the ASP can be successfully activated, the SGP or IPSP responds with one or more ASP Active Ack messages, including the associated Routing Context and Traffic Mode Type values. The Routing Context parameter MUST be included in the Asp Active Ack message if the received ASP Active message contained any Routing Contexts. Depending on the ASP Active Message Traffic Mode Type request, the SGP moves the ASP to the correct ASP traffic state within the associated Application Server(s). Layer Management is informed with an M-ASP_Active indication. If the SGP or IPSP receives any Data messages before an ASP Active message is received, the SGP or IPSP MAY discard them. By sending an ASP Active Ack message, the SGP or IPSP is now ready to receive and send traffic for the related Routing Context(s). The ASP SHOULD NOT send Data messages for the related Routing Context(s) before receiving an ASP Active Ack message, or it will risk message loss. Multiple ASP Active Ack messages MAY be used in response to an ASP Active message containing multiple Routing Contexts, allowing the SGP or IPSP to independently acknowledge the ASP Active message for different (sets of) Routing Contexts. The SGP or IPSP sends an Error message ("Invalid Routing Context") for each Routing Context value that the ASP cannot be successfully activated . In the case where an "out-of-the-blue" ASP Active message is received (i.e., the ASP has not registered with the SG or the SG has no static configuration data for the ASP), the message may be silently discarded. The SGP MUST send an ASP Active Ack message in response to a received ASP Active message from the ASP, if the ASP is already marked in the ASP-ACTIVE state at the SGP. Sidebottom et al [Page 74] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 At the ASP, the ASP Active Ack message received is not acknowledged. Layer Management is informed with an M-ASP_ACTIVE confirm primitive. It is possible for the ASP to receive Data message(s) before the ASP Active Ack message as the ASP Active Ack and Data messages from an SG or IPSP may be sent on different SCTP streams. Message loss is possible as the ASP does not consider itself in the ASP-ACTIVE state until reception of the ASP Active Ack message. When the ASP sends an ASP Active message it starts timer T(ack). If the ASP does not receive a response to an ASP Active message within T(ack), the ASP MAY restart T(ack) and resend ASP Active messages until it receives an ASP Active Ack message. T(ack) is provisionable, with a default of 2 seconds. Alternatively, retransmission of ASP Active messages MAY be put under control of Layer Management. In this method, expiry of T(ack) results in an M-ASP_ACTIVE confirm primitive carrying a negative indication. There are six modes of Application Server traffic handling in the SGP M3UA layer - Over-ride, Over-ride (Standby), Load-share, Load-share (Standby), Broadcast and Broadcast Standby. The Traffic Mode Type parameter in the ASP Active message indicates the traffic handling mode used in a particular Application Server. If the SGP determines that the mode indicated in an ASP Active message is unsupported or incompatible with the mode currently configured for the AS, the SGP responds with an Error message ("Unsupported / Invalid Traffic Handling Mode"). If the Traffic Handling mode of the Application Server is not already known via configuration data, then the Traffic Handling mode indicated in the first ASP Active message causing the transition of the Application Server state to AS-ACTIVE MAY be used to set the mode. In the case of an Over-ride mode AS, reception of an ASP Active message at an SGP causes the (re)direction of all traffic for the AS to the ASP that sent the ASP Active message. Any previously active ASP in the AS is now considered to be in state ASP-INACTIVE and SHOULD no longer receive traffic from the SGP within the AS. The SGP or IPSP then MUST send a Notify message ("Alternate ASP-Active") to the previously active ASP in the AS, and SHOULD stop traffic to/from that ASP. The ASP receiving this Notify MUST consider itself now in the ASP-INACTIVE state, if it is not already aware of this via inter-ASP communication with the Over-riding ASP. In the case of Over-ride (Standby) mode the traffic is not started to the ASP until the currently active ASP transitions to the ASP-INACTIVE or ASP-DOWN state. At this point the ASP that sent the ASP Active message ("Over-Ride (Standby)") is moved to the ASP-ACTIVE state and the traffic is redirected. A second ASP Active Ack message with a new Traffic Mode Type ("Over-ride", previously "Over-ride(Standby)") is sent to the ASP. A Notify message ("Alternate ASP-Active") is not sent in this case. Sidebottom et al [Page 75] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 If there is no currently active ASP, an ASP Active Ack message ("Over- ride") is returned right away and the traffic is directed to the ASP. In the case of a Load-share mode AS, reception of an ASP Active message at an SGP or IPSP causes the direction of traffic to the ASP sending the ASP Active message, in addition to all the other ASPs that are currently active in the AS. The algorithm at the SGP for load-sharing traffic within an AS to all the active ASPs is implementation dependent. The algorithm could, for example, be round-robin or based on information in the Data message (e.g., the SLS, SCCP SSN, ISUP CIC value). An SGP or IPSP, upon reception of an ASP Active message for the first ASP in a Loadshare AS, MAY choose not to direct traffic to a newly active ASP until it determines that there are sufficient resources to handle the expected load (e.g., until there are "n" ASPs in state ASP- ACTIVE in the AS). In the case of a Load-share (Standby) mode AS, the traffic is not started to the ASP until the SGP or IPSP determines that there are insufficient resources available in the AS. This is likely when one of the active load-sharing ASPs transitions to either the ASP-INACTIVE or ASP-DOWN state. At this point the ASP that sent the ASP Active message ("Load-share (Standby)") is moved to the ASP_ACTIVE state and traffic is started. A second ASP Active Ack message with a new Traffic Mode Type ("Load-share" - previously "Loadshare(Standby)") is sent to the ASP. A Notify message ("Insufficient ASP resources active in AS ") is not sent in this case. If there is no currently active ASP, an ASP Active Ack message ("Loadshare") is returned right away and the traffic is directed to the ASP. All ASPs within a load-sharing mode AS must be able to process any Data message received for the AS, to accommodate any potential fail-over or rebalancing of the offered load. In the case of a Broadcast mode AS, reception of an ASP Active message at an SGP or IPSP cuases the direction of traffic to the ASP sending the ASP Active message, in addition to all the other ASPs that are currently active in the AS. The algorithm at the SGP for broadcasting traffic within an AS to all the active ASPs is a simple braoadcast algorithm, where every message is sent to each of the active ASPs. An SGP or IPSP, upon reception of an ASP Active message for the first ASP in a Broadcast AS, MAY choose not to direct traffic to a newly active ASP until it determines that there are sufficient resources to handle the expected load (e.g., until there are "n" ASPs in state ASP-ACTIVE in the AS). In the case of Broadcast (Standby) mode AS, the traffic is not started to the ASP until the SGP or IPSP determines that there are sufficient resuorces available in the AS. This is likely when one of the active broadcast ASPs transitions to either the ASP-INACTIVE or ASP-DOWN state. At this point the ASP that sent the ASP Active message ("Broadcast (Standby)") is moved to the ASP_ACTIVE state and traffic is started. A second ASP Active Ack message with a new Traffic Mode Type ("Broadcast" - previously "Broadcast (Standby)") is sent to the ASP. A Notify message ("Insufficient ASP resources active in AS") is not sent in this case. If there is no currently active ASP, an ASP Active Ack message ("Broadcast") is returned right away and the traffic is directed to the ASP. 4.2.3.5 ASP Inactive Procedures When an ASP wishes to withdraw from receiving traffic within an AS, the ASP sends an ASP Inactive message to the SGP or IPSP. This action MAY be initiated at the ASP by an M-ASP_INACTIVE request primitive from Layer Management or MAY be initiated automatically by an M3UA management function. In the case where an ASP is processing the traffic for more than one Application Server across a common SCTP association, the ASP Inactive message contains one or more Routing Contexts to indicate for which Application Servers the ASP Inactive message applies. In the case where an ASP Inactive message does not contain a Routing Context parameter, the receiver must know, via Sidebottom et al [Page 76] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 configuration data, which Application Servers the ASP is a member and move the ASP to the ASP-INACTIVE state in each all Application Servers. In the case of an Over-ride mode AS, where another ASP has already taken over the traffic within the AS with an ASP Active ("Over-ride") message, the ASP that sends the ASP Inactive message is already considered by the SGP to be in state ASP-INACTIVE. .An ASP Inactive Ack message is sent to the ASP, after ensuring that all traffic is stopped to the ASP. In the case of a Load-share mode AS, the SGP moves the ASP to the ASP- INACTIVE state and the AS traffic is re-allocated across the remaining ASPs in the state ASP-ACTIVE, as per the load-sharing algorithm currently used within the AS. A Notify message("Insufficient ASP resources active in AS") MAY be sent to all inactive ASPs, if required. However, if a Loadshare ("Standby") ASP is available, it may be now immediately included in the loadshare group and a Notify message is not sent. An ASP Inactive Ack message is sent to the ASP after all traffic is halted and Layer Management is informed with an M-ASP_INACTIVE indication primitive. In the case of a Broadcast mode AS, the SGP moves the ASP to the ASP-INACTIVE state and the AS traffic is broadcast only to the remaining ASPs in the state ASP-ACTIVE. A Notify message ("Insufficient ASP resources active in AS") MAY be sent to all inactive ASPs, if required. However, if a Broadcast ("Standby") ASP is available, it may be now immediately included in the broadcast group and a Notify message is not sent. An ASP Inactive Ack message is sent to the ASP after all traffic is halted and Layer Management is informed with an M-ASP_INACTIVE indication primitive. Multiple ASP Inactive Ack messages MAY be used in response to an ASP Inactive message containing multiple Routing Contexts, allowing the SGP or IPSP to independently acknowledge for different (sets of) Routing Contexts. The SGP or IPSP sends an Error message ("Invalid Routing Context") message for each invalid or un-configured Routing Context value in a received ASP Inactive message message. The SGP MUST send an ASP Inactive Ack message in response to a received ASP Inactive message from the ASP and the ASP is already marked as ASP- INACTIVE at the SGP. At the ASP, the ASP-Inactive Ack message received is not acknowledged. Layer Management is informed with an M-ASP_INACTIVE confirm primitive. When the ASP sends an ASP Inactive message it starts timer T(ack). If the ASP does not receive a response to an ASP Inactive message within T(ack), the ASP MAY restart T(ack) and resend ASP Inactive messages until it receives an ASP Inactive Ack message. T(ack) is provisionable, with a default of 2 seconds. Alternatively, retransmission of ASP Inactive messages MAY be put under control of Layer Management. In this method, expiry of T(ack) results in a M- ASP_Inactive confirm primitive carrying a negative indication. If no other ASPs in the Application Server are in the state ASP-ACTIVE or ASP-STANDBY, the SGP MUST send a Notify message ("AS-Pending") to all of the ASPs in the AS which are in the state ASP-INACTIVE. The SGP SHOULD start buffering the incoming messages for T(r)seconds, after which messages MAY be discarded. T(r) is configurable by the network operator. If the SGP receives an ASP Active message from an ASP in the AS before expiry of T(r), the buffered traffic is directed to that ASP and the timer is cancelled. If T(r) expires, the AS is moved to the AS-INACTIVE state. Sidebottom et al [Page 77] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 4.2.3.6 Notify Procedures A Notify message reflecting a change in the AS state MUST be sent to all ASPs in the AS, except those in the ASP-DOWN state, with appropriate Status Information and any ASP Identifier of the failed ASP. The Notify message MUST be sent after any ASP State or Traffic Management acknowledgement messages (e.g., ASP Up Ack, ASP Down Ack, ASP Active Ack, or ASP Inactive Ack). At the ASP, Layer Management is informed with an M-NOTIFY indication primitive. In the case where a Notify message("AS-PENDING") message is sent by an SGP that now has no ASPs active to service the traffic, or where a Notify message("Insufficient ASP resources active in AS") MUST be sent in the Loadshare or Broadcast mode, the Notify message does not explicitly compel the ASP(s) receiving the message to become active. The ASPs remain in control of what (and when) traffic action is taken. In the case where a Notify message does not contain a Routing Context parameter, the receiver must know, via configuration data, of which Application Servers the ASP is a member and take the appropriate action in each AS. 4.2.3.7 Heartbeat Procedures The optional Heartbeat procedures MAY be used when operating over transport layers that do not have their own heartbeat mechanism for detecting loss of the transport association (i.e., other than SCTP). After an ASP or IPSP has received an ASP Up Ack message from an M3UA peer in response to an ASP Up message, either M3UA peer may optionally send Heartbeat messages periodically, subject to a provisionable timer T(beat). Upon receiving a Heartbeat message, the M3UA peer MUST respond with a Heartbeat Ack message. If no Heartbeat Ack message (or any other M3UA message) is received from the M3UA peer within 2*T(beat), the remote M3UA peer is considered unavailable. Transmission of Heartbeat messages is stopped and the signalling process SHOULD attempt to re-establish communication if it is configured as the client for the disconnectd M3UA peer. The Heartbeat message may optionally contain an opaque Heartbeat Data parameter that MUST be echoed back unchanged in the related Heartbeat Ack message. The sender, upon examining the contents of the returned Heartbeat Ack message, MAY choose to consider the remote M3UA peer as unavailable. The contents/format of the Heartbeat Data parameter is implementation-dependent and only of local interest to the original sender. The contents may be used, for example, to support a Heartbeat sequence algorithm (to detect missing Heartbeats), and/or a timestamp mechanism (to evaluate delays). Sidebottom et al [Page 78] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Note: Heartbeat related events are not shown in Figure 4 "ASP state transition diagram". 4.2.4 Routing Key Management Procedures 4.2.4.1 Registration An ASP MAY dynamically register with an SGP as an ASP within an Application Server using the REG REQ message. A Routing Key parameter in the REG REQ message specifies the parameters associated with the Routing Key. The SGP examines the contents of the received Routing Key parameter and compares it with the currently provisioned Routing Keys. If the received Routing Key matches an existing SGP Routing Key entry, and the ASP is not currently included in the list of ASPs for the related Application Server, the SGP MAY authorize the ASP to be added to the AS. Or, if the Routing Key does not currently exist and the received Routing Key data is valid and unique, an SGP supporting dynamic configuration MAY authorize the creation of a new Routing Key and related Application Server and add the ASP to the new AS. In either case, the SGP returns a Registration Response message to the ASP, containing the same Local-RK-Identifier as provided in the initial request, and a Registration Result "Successfully Registered". A unique Routing Context value assigned to the SGP Routing Key is included. The method of Routing Context value assignment at the SGP is implementation dependent but must be guaranteed to be unique for each Application Server or Routing Key supported by the SGP. If the SGP determines that the received Routing Key data is invalid, or contains invalid parameter values, the SGP returns a Registration Response message to the ASP, containing a Registration Result "Error - Invalid Routing Key", "Error - Invalid DPC", "Error - Invalid Network Appearance" as appropriate. If the SGP determines that a unique Routing Key cannot be created, the SGP returns a Registration Response message to the ASP, with a Registration Status of "Error - "Cannot Support Unique Routing" An incoming signalling message received at an SGP should not match against more than one Routing Key. If the SGP does not authorize the registration request, the SGP returns a REG RSP message to the ASP containing the Registration Result "Error - Permission Denied". If an SGP determines that a received Routing Key does not currently exist and the SGP does not support dynamic configuration, the SGP returns a Registration Response message to the ASP, containing a Registration Result "Error - Routing Key not Currently Provisioned". Sidebottom et al [Page 79] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 If an SGP determines that a received Routing Key does not currently exist and the SGP supports dynamic configuration but does not have the capacity to add new Routing Key and Application Server entries, the SGP returns a Registration Response message to the ASP, containing a Registration Result "Error - Insufficient Resources". If an SGP determines that one or more of the Routing Key parameters are not supported for the purpose of creating new Routing Key entries, the SGP returns a Registration Response message to the ASP, containing a Registration Result "Error - Unsupported RK parameter field". This result MAY be used if, for example, the SGP does not support RK Circuit Range Lists in a Routing Key because the SGP does not support ISUP traffic, or does not provide CIC range granularity. A Registration Response "Error - Unsupported Traffic Handling Mode" is returned if the Routing Key in the REG REQ contains an Traffic Handling Mode that is inconsistent with the presently configured mode for the matching Application Server. An ASP MAY register multiple Routing Keys at once by including a number of Routing Key parameters in a single REG REQ message. The SGP MAY respond to each registration request in a single REG RSP message, indicating the success or failure result for each Routing Key in a separate Registration Result parameter. Alternatively the SGP MAY respond with multiple REG RSP messages, each with one or more Registration Result parameters. The ASP uses the Local-RK-Identifier parameter to correlate the requests with the responses. Upon successful registration of an ASP in an AS, the SGP can now send related SS7 Signalling Network Management messaging, if this did not previously start upon the ASP transitioning to state ASP-INACTIVE 4.2.4.2 Deregistration An ASP MAY dynamically deregister with an SGP as an ASP within an Application Server using the DEREG REQ message. A Routing Context parameter in the DEREG REQ message specifies which Routing Keys to de- register. An ASP SHOULD move to the ASP-INACTIVE state for an Application Server before attempting to deregister the Routing Key (i.e., deregister after receiving an ASP Inactive Ack). Also, an ASP SHOULD deregister from all Application Servers that it is a member before attempting to move to the ASP-Down state. The SGP examines the contents of the received Routing Context parameter and validates that the ASP is currently registered in the Application Server(s) related to the included Routing Context(s). If validated, the ASP is de-registered as an ASP in the related Application Server. Sidebottom et al [Page 80] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The deregistration procedure does not necessarily imply the deletion of Routing Key and Application Server configuration data at the SGP. Other ASPs may continue to be associated with the Application Server, in which case the Routing Key data MUST NOT be deleted. If a Deregistration results in no more ASPs in an Application Server, an SGP MAY delete the Routing Key data. The SGP acknowledges the deregistration request by returning a DEREG RSP message to the requesting ASP. The result of the deregistration is found in the Deregistration Result parameter, indicating success or failure with cause. An ASP MAY deregister multiple Routing Contexts at once by including a number of Routing Contexts in a single DEREG REQ message. The SGP MAY respond to each deregistration request in a single DEREG RSP message, indicating the success or failure result for each Routing Context in a separate Deregistration Result parameter. 4.3 Procedures to Support the Availability or Congestion Status of SS7 Destination 4.3.1 At an SGP On receiving an MTP-PAUSE, MTP-RESUME or MTP-STATUS indication primitive from the nodal inter-working function at an SGP, the SGP M3UA layer will send a corresponding SS7 Signalling Network Management (SSNM) DUNA, DAVA, SCON, or DUPU message (see Section 3.4) to the M3UA peers at concerned ASPs. The M3UA layer must fill in various fields of the SSNM messages consistently with the information received in the primitives. The SGP M3UA layer determines the set of concerned ASPs to be informed based on the specific SS7 network for which the primitive indication is relevant. In this way, all ASPs configured to send/receive traffic within a particular network appearance are informed. If the SGP operates within a single SS7 network appearance, then all ASPs are informed. DUNA, DAVA, SCON, and DRST messages MUST be sent sequentially and processed at the receiver in the order sent. SCTP stream "0" is used to provide the sequencing. The only exception to this is if the international congestion method (see Q.704) is used. If so, the Unordered bit in the SCTP DATA chunk MAY be used for the SCON message. Sidebottom et al [Page 81] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Sequencing is not required for the DUPU or DAUD messages, which MAY be sent un-sequenced. Again, SCTP stream 0 is used, with optional use of the Unordered bit in the SCTP DATA chunk. 4.3.2 At an ASP 4.3.2.1 Single SGP Configurations At an ASP, upon receiving an SS7 Signalling Network Management (SSNM) message from the remote M3UA Peer, the M3UA layer invokes the appropriate primitive indications to the resident M3UA-Users. Local management is informed. In the case where a local event has caused the unavailability or congestion status of SS7 destinations, the M3UA layer at the ASP SHOULD pass up appropriate indications in the primitives to the M3UA User, as though equivalent SSNM messages were received. For example, the loss of an SCTP association to an SGP may cause the unavailability of a set of SS7 destinations. MTP-PAUSE indication primitives to the M3UA User are appropriate. Implementation Note: To accomplish this, the M3UA layer at an ASP maintains the status of routes via the SG(P), much like an MTP3 layer maintains route-set status. 4.3.2.2 Multiple SGP Configurations At an ASP, upon receiving a Signalling Network Management message from the remote M3UA Peer, the M3UA layer updates the status of the affected route(s) via the originating SGP and determines, whether or not the overall availability or congestion status of the effected destination(s) has changed. If so, the M3UA layer invokes the appropriate primitive indications to the resident M3UA-Users. Local management is informed. 4.3.3 ASP Auditing An ASP may optionally initiate an audit procedure to enquire of an SGP the availability and, if the national congestion method with multiple congestion levels and message priorities is used, congestion status of an SS7 destination or set of destinations. A Destination Audit (DAUD) message is sent from the ASP to the SGP requesting the current availability and congestion status of one or more SS7 Destination Point Codes. The DAUD message MAY be sent un-sequenced. The DAUD MAY be sent by the ASP in the following cases: Sidebottom et al [Page 82] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 - Periodic. A Timer originally set upon reception of a DUNA, SCON or DRST message has expired without a subsequent DAVA, DUNA, SCON or DRST message updating the availability/congestion status of the affected Destination Point Codes. The Timer is reset upon issuing a DAUD. In this case the DAUD is sent to the SGP that originally sent the SSNM message. - Isolation. The ASP is newly ASP-INACTIVE or ASP-ACTIVE or has been isolated from an SGP for an extended period. The ASP MAY request the availability/congestion status of one or more SS7 destinations to which it expects to communicate. In the first of the cases above, the auditing procedure must not be invoked for the case of a received SCON message containing a congestion level value of "no congestion" or undefined" (i.e., congestion Level = "0"). This is because the value indicates either congestion abatement or that the ITU MTP3 international congestion method is being used. In the international congestion method, the MTP3 layer at the SGP does not maintain the congestion status of any destinations and therefore the SGP cannot provide any congestion information in response to the DAUD. For the same reason, in the second of the cases above a DAUD message cannot reveal any congested destination(s). The SGP MUST respond to a DAUD message with the MTP3 availability/congested status of the routeset associated with each Destination Point Code(s) in the DAUD message. The status of each SS7 destination requested is indicated in a DUNA message (if unavailable), a DAVA message (if available), or a DRST (if restricted and the SGP supports this feature). If the SS7 destination is available and congested, the SGP responds with an SCON message in addition to the DAVA message. If the SS7 destination is restricted and congested, the SGP responds with an SCON message in addition to the DRST. If the SGP has no information on the availability/congestion status of the SS7 destination, the SGP responds with a DUNA message, as it has no routing information to allow it to route traffic to this destination Any DUNA or DAVA message in response to a DAUD message MAY contain a list of up to sixteen Affected Point Codes. 4.4 MTP3 Restart In the case where the MTP3 in the SG undergoes an MTP restart, event communication SHOULD be handled as follows: When the SG discovers SS7 network isolation, the SGPs send an indication to all concerned available ASPs (i.e., ASPs in the ASP- ACTIVE, ASP-STANDBY or ASP-INACTIVE state) using a DUNA message. For the purpose of MTP restart, all Signalling Point Management Clusters with point codes Sidebottom et al [Page 83] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 different from that of the SG with at least one ASP in the ASP-ACTIVE state or that has sent an ASP ACTIVE message to the SG during the first part of the restart procedure should be considered as available. If the M3UA layer at the SGP receives any ASP ACTIVE messages during the restart procedure, it delays the ASP ACTIVE ACK messages until the end of the restart procedure. During the second part of the restart procedure the SGP M3UA layers at the SGPs inform all concerned ASPs in the ASP-ACTIVE, ASP-STANDBY or ASP-INACTIVE states of any unavailable/restricted SS7 destinations using the DUNA/DRST message. At the end of the restart procedure the SGP M3UA layers send an ASP ACTIVE ACK message to all ASPs in the ASP-ACTIVE state. When the M3UA layer at an ASP receives a DUNA message indicating SS7 network isolation at an SG, it will stop any affected traffic via this route. When the M3UA subsequently receives any DUNA messages from an SGP it will mark the affected SS7 destinations as unavailable via that SG. When the M3UA receives an ASP ACTIVE ACK message it can resume traffic to available SS7 destinations via this SGP, provided the ASP is in the ASP-ACTIVE state towards this SGP. The ASP MAY choose to audit the availability of any unavailable destinations 5. Examples of M3UA Procedures 5.1 Establishment of Association and Traffic between SGPs and ASPs 5.1.1 Single ASP in an Application Server ("1+0" sparing), 5.1.1.1 Single ASP in an Application Server ("1+0" sparing), No Registration This scenario shows the example M3UA message flows for the establishment of traffic between an SGP and an ASP, where only one ASP is configured within an AS (no backup). It is assumed that the SCTP association is already set-up. The sending of any DUNA/SCON messages by the SGP is not shown but is similar to the case described in Section 5.1.2. SGP ASP1 | | |<-------------ASP Up------------| |-----------ASP Up Ack---------->| | | |<------- ASP Active(RCn)--------| RC: Routing Context |-----ASP Active Ack (RCn)------>| (optional) | | Note: If the ASP Active message contains an optional Routing Context parameter, The ASP Active message only applies for the specified RC value(s). For an unknown RC value, the SGP responds with an Error message. Sidebottom et al [Page 84] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 5.1.1.2 Single ASP in Application Server ("1+0" sparing), Dynamic Registration This scenario is the same as for 5.1.1.1 but with the optional exchange of registration information. In this case the Registration is accepted by the SGP. SGP ASP1 | | |<------------ASP Up-------------| |----------ASP Up Ack----------->| | | |<----REGISTER REQ(LRCn,RKn)-----| LRC: Local Routing | | Context |----REGISTER RESP(LRCn,RCn)---->| RK: Routing Key | | RC: Routing Context | | |<------- ASP Active(RCn)--------| |-----ASP Active Ack (RCn)------>| | | Note: In the case of an unsuccessful registration attempt (e.g., Invalid RKn), the Register Response message will contain an unsuccessful indication and the ASP will not subsequently send an ASP Active message. 5.1.1.3 Single ASP in Multiple Application Servers (each with "1+0" sparing), Dynamic Registration (Case 1 - Multiple Registration Requests) SGP ASP1 | | |<------------ASP Up-------------| |----------ASP Up Ack----------->| | | |<----REGISTER REQ(LRC1,RK1)-----| LRC: Local Routing | | Context |----REGISTER RESP(LRC1,RC1)---->| RK: Routing Key | | RC: Routing Context | | |<------- ASP Active(RC1)--------| |-----ASP Active Ack (RC1)------>| | | | | |<----REGISTER REQ(LRCn,RKn)-----| | | |----REGISTER RESP(LRCn,RCn)---->| | | | | |<------- ASP Active(RCn)--------| |-----ASP Active Ack (RCn)------>| | | Sidebottom et al [Page 85] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Note: In the case of an unsuccessful registration attempt (e.g., Invalid RKn), the Register Response message will contain an unsuccessful indication and the ASP will not subsequently send an ASP Active message. Each LRC/RK pair registration is considered independently. It is not necessary to follow a Registration Request/Response message pair with an ASP Active message before sending the next Registration Request. The ASP Active message can be sent at any time after the related successful registration. 5.1.1.4 Single ASP in Multiple Application Servers (each with "1+0" sparing), Dynamic Registration (Case 2 - Single Registration Request) SGP ASP1 | | |<------------ASP Up-------------| |----------ASP Up Ack----------->| | | |<---REGISTER REQ({LRC1,RK1},----| | ..., | | {LRCn,RKn}),----| | | |---REGISTER RESP({LRC1,RC1},--->| | ..., | | (LRCn,RCn}) | | | |<------- ASP Active(RC1)--------| |-----ASP Active Ack (RC1)------>| | | : : : : | | |<------- ASP Active(RCn)--------| |-----ASP Active Ack (RCn)------>| | | Note: In the case of an unsuccessful registration attempt (e.g., Invalid RKn), the Register Response message will contain an unsuccessful indication and the ASP will not subsequently send an ASP Active message. Each LRC/RK pair registration is considered independently. The ASP Active message can be sent at any time after the related successful registration, and may have more than one RC. Sidebottom et al [Page 86] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 5.1.2 Two ASPs in Application Server ("1+1" sparing) This scenario shows the example M3UA message flows for the establishment of traffic between an SGP and two ASPs in the same Application Server, where ASP1 is configured to be in the ASP-ACTIVE state and ASP2 is to be a "back-up" in the event of communication failure or the withdrawal from service of ASP1. ASP2 may act as a hot, warm, or cold back-up depending on the extent to which ASP1 and ASP2 share call/transaction state or can communicate call state under failure/withdrawal events. The example message flow is the same whether the ASP Active messages indicate "Over-ride", "Load-share" or "Broadcast" mode, although typically this example would use an Over-ride mode. The SGP MAY start sending any relevant DUNA, DRST and SCON messages to ASPs as soon as they enter the ASP-INACTIVE state. In the case of MTP Restart, the ASP-Active Ack message is only sent after all relevant DUNA/DRST/SCON messages have been transmitted to the concerned ASP. SGP ASP1 ASP2 | | | |<--------ASP Up----------| | |-------ASP Up Ack------->| | | | | |<-----------------------------ASP Up----------------| |-----------------------------ASP Up Ack------------>| | | | | | | |<-------ASP Active-------| | |------ASP Active Ack---->| | | | | Note: It is also possible for ASP2 to send an ASP-Active ("Over-ride- Standby") message after ASP1 goes ASP-ACTIVE A similar sparing arrangement is created, except that the SGP may re-direct traffic to ASP2 more quickly in certain fail-over cases. 5.1.3 Two ASPs in an Application Server ("1+1" sparing, load-sharing case) This scenario shows a similar case to Section 5.1.2 but where the two ASPs are brought to the state ASP-ACTIVE and subsequently load-share the traffic. In this case, one ASP is sufficient to handle the total traffic load. The sending of DUNA, DRST and SCON messages by the SGP is not shown but is similar to the case described in Section 5.1.2. Sidebottom et al [Page 87] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 SGP ASP1 ASP2 | | | |<---------ASP Up---------| | |--------ASP Up Ack------>| | | | | |<------------------------------ASP Up---------------| |-----------------------------ASP Up Ack------------>| | | | | | | |<--ASP Active (Ldshr)----| | |-----ASP-Active Ack----->| | | | | |----------------------------NOTIFY (AS-ACTIVE------>| | | | |<----------------------------ASP Active (Ldshr)-----| |-------------------------------ASP Active Ack------>| | | | 5.1.4 Three ASPs in an Application Server ("n+k" sparing, load-sharing case) This scenario shows the example M3UA message flows for the establishment of traffic between an SGP and three ASPs in the same Application Server, where two of the ASPs are brought to the state ASP- ACTIVE and subsequently share the load. In this case, a minimum of two ASPs are required to handle the total traffic load (2+1 sparing). The sending of DUNA, DRST and SCON messages by the SGP is not shown but is similar to the case described in Section 5.1.2. SGP ASP1 ASP2 ASP3 | | | | |<------ASP Up-------| | | |-----ASP Up Ack---->| | | | | | | |<--------------------------ASP Up-------| | |-------------------------ASP Up Ack---->| | | | | | |<---------------------------------------------ASP Up--------| |---------------------------------------------ASP Up Ack---->| | | | | | | | | |<--ASP Act (Ldshr)--| | | |----ASP Act Ack---->| | | | | | | -----------Notify (AS-ACTIVE)----------->| | |-----------------------Notify (AS-ACTIVE)------------------>| | | | | |<--------------------ASP Act. (Ldshr)---| | |-----------------------ASP Act Ack----->| | | | | | Sidebottom et al [Page 88] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Note: It is also possible for ASP3 to send an ASP Active message ("Loadshare-Standby") after ASP1 and ASP2 go to the ASP-ACTIVE state A similar sparing arrangement is created, except that the SGP may redirect traffic to ASP3 more quickly in certain fail-over cases. 5.2 ASP Traffic Fail-over Examples 5.2.1 (1+1 Sparing, Withdrawal of ASP, Back-up Over-ride) Following on from the example in Section 5.1.2, and ASP1 withdraws from service: SGP ASP1 ASP2 | | | |<-----ASP Inactive-------| | |----ASP Inactive Ack---->| | |------------------------NTFY(AS-Pending)----------->| | | | |<------------------------------ ASP Active----------| |------------------------------ASP Active Ack------->| | | Note: If the SGP M3UA layer detects the loss of the M3UA peer (M3UA heartbeat loss or detection of SCTP failure), the initial ASP Inactive message exchange (i.e., SGP to ASP1) would not occur. 5.2.2 (1+1 Sparing, Back-up Over-ride) Following on from the example in Section 5.1.2, ASP2 wishes to over-ride ASP1 and take over the traffic: SGP ASP1 ASP2 | | | |<------------------------------ ASP Active----------| |-------------------------------ASP Active Ack------>| |----NTFY(Alt ASP-Act)--->| | | | 5.2.3 (n+k Sparing, Load-sharing case, Withdrawal of ASP) Following on from the example in Section 5.1.4, and ASP1 withdraws from service: Sidebottom et al [Page 89] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 SGP ASP1 ASP2 ASP3 | | | | |<----ASP Inact.-----| | | |---ASP Inact Ack--->| | | | | | | |---------------------------------NTFY(Ins. ASPs)----------->| | | | | |<-----------------------------------------ASP Act (Ldshr)---| |-------------------------------------------ASP Act (Ack)--->| | | | | For the Notify message to be sent, the SG maintains knowledge of the minimum ASP resources required (e.g., if the SG knows that "n+k" = "2+1" for a load-share AS and "n" currently equals "1"). Note: If the SGP detects loss of the ASP1 M3UA peer (M3UA heartbeat loss or detection of SCTP failure), the initial ASP Inactive message exchange (i.e., SGP-ASP1) would not occur. 5.3 Normal Withdrawal of an ASP from an Application Server and Tear- down of an Association An ASP which is now confirmed in the state ASP-INACTIVE (i.e., the ASP has received an ASP Inactive Ack message) may now proceed to the ASP- DOWN state, if it is to be removed from service. Following on from Section 5.2.1 or 5.2.3, where ASP1 has moved to the "Inactive" state: SGP ASP1 | | |<-----ASP Inactive (RCn)-------| RC: Routing Context |----ASP Inactive Ack (RCn)---->| | | |<-----DEREGISTER REQ(RCn)------| See Notes | | |---DEREGISTER RESP(LRCn,RCn)-->| | | : : | | |<-----------ASP Down-----------| |---------ASP Down Ack--------->| | | Note: The Deregistration procedure MUST be used if the ASP previously used the Registration procedures for configuration within the Application Server. ASP Inactive and Deregister messages exchanges may contain multiple Routing Contexts. Sidebottom et al [Page 90] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 The ASP SHOULD be in the ASP-INACTIVE state and SHOULD have deregistered in all its Routing Contexts before attempting to move to the ASP-DOWN state. 5.4 M3UA/MTP3-User Boundary Examples 5.4.1 At an ASP This section describes the primitive mapping between the MTP3 User and the M3UA layer at an ASP. 5.4.1.1 Support for MTP-TRANSFER Primitives at the ASP 5.4.1.1.1 Support for MTP-TRANSFER Request Primitive When the MTP3-User on the ASP has data to send into the SS7 network, it uses the MTP-TRANSFER request primitive. The M3UA layer at the ASP will do the following when it receives an MTP-TRANSFER request primitive from the M3UA user: - Determine the correct SGP; - Determine the correct association to the chosen SGP; - Determine the correct stream in the association (e.g., based on SLS); - Determine whether to complete the optional fields of the DATA message; - Map the MTP-TRANSFER request primitive into the Protocol Data field of a DATA message; - Send the DATA message to the remote M3UA peer at the SGP, over the SCTP association. SGP ASP | | |<-----DATA Message-------|<--MTP-TRANSFER req. | | 5.4.1.1.2 Support for the MTP-TRANSFER Indication Primitive When the M3UA layer on the ASP receives a DATA message from the remote M3UA peer at the SGP, it will do the following: - Evaluate the optional fields of the DATA message, if present; Sidebottom et al [Page 91] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 - Map the Protocol Data field of a DATA message into the MTP-TRANSFER indication primitive; - Pass the MTP-TRANSFER indication primitive to the user part. In case of multiple user parts, the optional fields of the Data message are used to determine the concerned user part. SGP ASP | | |------Data Message------>|-->MTP-Transfer ind. | | 5.4.1.1.3 Support for ASP Querying of SS7 Destination States There are situations such as temporary loss of connectivity to the SGP that may cause the M3UA layer at the ASP to audit SS7 destination availability/congestion states. Note: there is no primitive for the MTP3-User to request this audit from the M3UA layer as this is initiated by an internal M3UA management function. SGP ASP | | |<----------DAUD----------| |<----------DAUD----------| |<----------DAUD----------| | | | | 5.4.2 At an SGP This section describes the primitive mapping between the MTP3-User and the M3UA layer at an SGP. 5.4.2.1 Support for MTP-TRANSFER Request Primitive at the SGP When the M3UA layer at the SGP has received DATA messages from its peer destined to the SS7 network it will do the following: - Evaluate the optional fields of the DATA message, if present, to determine the Network Appearance; - Map the Protocol data field of the DATA message into an MTP- TRANSFER request primitive; - Pass the MTP-TRANSFER request primitive to the MTP3 of the concerned Network Appearance. Sidebottom et al [Page 92] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 SGP ASP | | <---MTP-TRANSFER req.|<---------DATA ----------| | | 5.4.2.2 Support for MTP-TRANSFER Indication Primitive at the SGP When the MTP3 layer at the SGP has data to pass its user parts, it will use the MTP-TRANSFER indication primitive. The M3UA layer at the SGP will do the following when it receives an MTP-TRANSFER indication primitive: - Determine the correct ASP using the distribution function; - Select an ASP in the ASP-ACTIVE state - Determine the correct association to the chosen ASP; - Determine the correct stream in the SCTP association (e.g., based on SLS); - Determine whether to complete the optional fields of the DATA message; - Map the MTP-TRANSFER indication primitive into the Protocol Data field of a DATA message; - Send the DATA message to the remote M3UA peer in the ASP, over the SCTP association SGP ASP | | --MTP-TRANSFER ind.->|----------DATA --------->| | | 5.4.2.3 Support for MTP-PAUSE, MTP-RESUME, MTP-STATUS Indication Primitives The MTP-PAUSE, MTP-RESUME and MTP-STATUS indication primitives from the MTP3 upper layer interface at the SGP need to be made available to the remote MTP3 User Part lower layer interface at the concerned ASP(s). 5.4.2.3.1 Destination Unavailable The MTP3 layer at the SGP will generate an MTP-PAUSE indication primitive when it determines locally that an SS7 destination is unreachable. The M3UA layer will map this primitive to a DUNA message. The SGP M3UA layer determines the set of concerned ASPs to be informed based on internal SS7 network information associated with the MTP-PAUSE indication primitive indication. Sidebottom et al [Page 93] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 SGP ASP | | --MTP-PAUSE ind.-->|---------DUNA----------->|--MTP-PAUSE ind.--> | | 5.4.2.3.2 Destination Available The MTP3 at the SGP will generate an MTP-RESUME indication primitive when it determines locally that an SS7 destination that was previously unreachable is now reachable. The M3UA layer will map this primitive to a DAVA message. The SGP M3UA determines the set of concerned ASPs to be informed based on internal SS7 network information associated with the MTP-RESUME indication primitive. SGP ASP | | --MTP-RESUME ind.-->|-----------DAVA--------->|--MTP-RESUME ind.--> | | 5.4.2.3.3 SS7 Network Congestion The MTP3 layer at the SGP will generate an MTP-STATUS indication primitive when it determines locally that the route to an SS7 destination is congested. The M3UA layer will map this primitive to a SCON message. It will determine which ASP(s) to send the SCON message to, based on the intended Application Server. SGP ASP | | --MTP-STATUS ind.-->|-----------SCON--------->|--MTP-STATUS ind.--> | | 5.4.2.3.4 Destination User Part Unavailable The MTP3 layer at the SGP will generate an MTP-STATUS indication primitive when it receives an UPU message from the SS7 network. The M3UA layer will map this primitive to a DUPU message. It will determine which ASP(s) to send the DUPU based on the intended Application Server. SGP ASP | | --MTP-STATUS ind.-->|----------DUPU---------->|--MTP-STATUS ind.--> | | Sidebottom et al [Page 94] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 6. Security 6.1 Introduction M3UA is designed to carry signalling messages for telephony services. As such, M3UA must involve the security needs of several parties: the end users of the services; the network providers and the applications involved. Additional requirements may come from local regulation. While having some overlapping security needs, any security solution should fulfil all of the different parties' needs. 6.2 Threats There is no quick fix, one-size-fits-all solution for security. As a transport protocol, M3UA has the following security objectives: * Availability of reliable and timely user data transport. * Integrity of user data transport. * Confidentiality of user data. M3UA is recommended to be transported on SCTP. SCTP [13] provides certain transport related security features, such as some protection against: * Blind Denial of Service Attacks * Flooding * Masquerade * Improper Monopolization of Services When M3UA is running in professionally managed corporate or service provider network, it is reasonable to expect that this network includes an appropriate security policy framework. The "Site Security Handbook" [21] should be consulted for guidance. When the network in which M3UA runs in involves more than one party, it may not be reasonable to expect that all parties have implemented security in a sufficient manner. In such a case, it is recommended that IPSEC is used to ensure confidentiality of user payload. Consult [22] for more information on configuring IPSEC services. 6.3 Protecting Confidentiality Particularly for mobile users, the requirement for confidentiality may include the masking of IP addresses and ports. In this case application level encryption is not sufficient; IPSEC ESP [23] SHOULD be used instead. Regardless of which level performs the encryption, the IPSEC ISAKMP [24] service SHOULD be used for key management. Sidebottom et al [Page 95] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 7. IANA Considerations 7.1 SCTP Payload Protocol Identifier IANA has assigned an M3UA value for the Payload Protocol Identifier in the SCTP DATA chunk. The following SCTP Payload Protocol Identifier is registered: M3UA "3" The SCTP Payload Protocol Identifier value "3" SHOULD be included in each SCTP DATA chunk, to indicate that the SCTP is carrying the M3UA protocol. The value "0" (unspecified) is also allowed but any other values MUST not be used. This Payload Protocol Identifier is not directly used by SCTP but MAY be used by certain network entities to identify the type of information being carried in a DATA chunk. The User Adaptation peer MAY use the Payload Protocol Identifier as a way of determining additional information about the data being presented to it by SCTP. 7.2 M3UA Port Number IANA has registered SCTP (and UDP/TCP) Port Number 2905 for M3UA. 7.3 M3UA Protocol Extensions This protocol may also be extended through IANA in three ways: -- through definition of additional message classes, -- through definition of additional message types, and -- through definition of additional message parameters The definition and use of new message classes, types and parameters is an integral part of SIGTRAN adaptation layers. Thus these extensions are assigned by IANA through an IETF Consensus action as defined in Guidelines for Writing an IANA Considerations Section in RFCs (25] The proposed extension must in no way adversely affect the general working of the protocol. 7.3.1 IETF Defined Message Classes The documentation for a new message class MUST include the following information: (a) A long and short name for the new message class; (b) A detailed description of the purpose of the message class. 7.3.2 IETF Defined Message Types The documentation for a new message type MUST include the following information: Sidebottom et al [Page 96] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 (a) A long and short name for the new message type; (b) A detailed description of the structure of the message;. (c) A detailed definition and description of intended use for each field within the message; (d) A detailed procedural description of the use of the new message type within the operation of the protocol; (e) A detailed description of error conditions when receiving this message type. When an implementation receives a message type which it does not support, it MUST respond with an Error (ERR) message ("Unsupported Message Type"). 7.3.3 IETF Defined Parameter Extension Documentation of the message parameter MUST contain the following information: (a) Name of the parameter type; (b) Detailed description of the structure of the parameter field. This structure MUST conform to the general type-length-value format described in Section 3.2; (c) Detailed definition of each component of the parameter value; (d) Detailed description of the intended use of this parameter type, and an indication of whether and under what circumstances multiple instances of this parameter type may be found within the same message. 8. Acknowledgements The authors would like to thank Antonio Roque Alvarez, Joyce Archibald, Tolga Asveren, Maria-Cruz Bartolome-Rodrigo, Dan Brendes, Nikhil Jain, Joe Keller, Kurt Kite, Ming Lin, Steve Lorusso, John Loughney, Naoto Makinae, Howard May, Barry Nagelberg, Neil Olson, Heinz Prantner, Shyamal Prasad, Mukesh Punhani, Selvam Rengasami, Ray Singh, Michael Tuexen, Nitin Tomar, Gery Verwimp, Kazuo Watanabe, Ben Wilson and many others for their valuable comments and suggestions. 9. References [1] RFC 2719, "Framework Architecture for Signaling Transport", L. Ong et al, October 1999 [2] ITU-T Recommendations Q.761 to Q.767, "Signalling System No.7 (SS7) - ISDN User Part (ISUP)" [3] ANSI T1.113 - "Signaling System Number 7 - ISDN User Part" Sidebottom et al [Page 97] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 [4] ETSI ETS 300 356-1 "Integrated Services Digital Network (ISDN); Signalling System No.7; ISDN User Part (ISUP) version 2 for the international interface; Part 1: Basic services" [5] ITU-T Recommendations Q.711 to Q.715, "Signalling System No. 7 (SS7) - Signalling Connection Control Part (SCCP)" [6] ANSI T1.112 "Signaling System Number 7 - Signaling Connection Control Part" [7] ETSI ETS 300 009-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Signalling Connection Control Part (SCCP) (connectionless and connection-oriented class 2) to support international interconnection; Part 1: Protocol specification" [8] ITU-T Recommendation Q.720, "Telephone User Part" [9] ITU-T Recommendations Q.771 to Q.775 "Signalling System No. 7 (SS7) - Transaction Capabilities (TCAP)" [10] ANSI T1.114 "Signaling System Number 7 - Transaction Capabilities Application Part" [11] ETSI ETS 300 287-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Transaction Capabilities (TC) version 2; Part 1: Protocol specification" [12] 3G TS 25.410 V4.0.0 (2001-04) "Technical Specification - 3rd Generation partnership Project; Technical Specification Group Radio Access Network; UTRAN Iu Interface: General Aspects and Principles" [13] RFC 2960, "Stream Control Transport Protocol", R. Stewart et al, October 2000. [14] ITU-T Recommendations Q.701 to Q.705, "Signalling System No. 7 (SS7) - Message Transfer Part (MTP)" [15] ANSI T1.111 "Signaling System Number 7 - Message Transfer Part" [16] ETSI ETS 300 008-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Message Transfer Part (MTP) to support international interconnection; Part 1: Protocol specification" [17] ITU-T Recommendation Q.2140 "B-ISDN ATM Adaptation Layer - Service Specific Coordination Function for signalling at the Network Node Interface (SSCF at NNI)" [18] ITU-T Recommendation Q.2110 "B-ISDN ATM Adaptation Layer - Service Specific Connection Oriented Protocol (SSCOP)" Sidebottom et al [Page 98] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 [19] RFC 2119, "Key words for use in RFCs to Indicate Requirement Levels", S. Bradner, March 1997. [20] ITU-T Recommendation Q.2210 "Message Transfer Part Level 3 functions and messages using the services of ITU Recommendation Q.2140" [21] RFC 2196, "Site Security Handbook", B. Fraser Ed., September 1997 [22] RFC 2401, "Security Architecture for the Internet Protocol", S. Kent, R. Atkinson, November 1998. [23] RFC 2406, "IP Encapsulating Security Payload (ESP)", S.Kent and R. Atkinson, November 1998. [24] RFC 2408, "Internet Security Association and Key Management Protocol", D. Maughan, M. Schertler, M. Schneider and J. Turner, November 1998. [25] RFC 2434, "Guidelines for Writing an IANA Considerations Section in RFCs", T. Narten and H. Alvestrand, October 1998 10. Bibliography [26] <draft-ietf-sigtran-m2ua-09.txt>, "MTP2-User Adaptation Layer", K. Morneault et al, July 2001 (Work in Progress) [27]<draft-ietf-sigtran-m2pa-02.txt>, "SS7 MTP2-User Peer-to-Peer Adaptation Layer", Tom George et al (Work in Progress) 11. Author's Addresses Greg Sidebottom Kanata, Ontario, Canada gregside@home.com Guy Mousseau Nortel Networks 3685 Richmond Rd Nepean, Ontario, Canada K2H 5B7 Lyndon Ong Ciena 10480 Ridgeview Court Cupertino, CA 95014 lyong@ciena.com Ian Rytina Ericsson Australia 37/360 Elizabeth Street Melbourne, Victoria 3000, Australia ian.rytina@ericsson.com.au Sidebottom et al [Page 99] Internet Draft SS7 MTP3-User Adaptation Layer Jul 2001 Hanns Juergen Schwarzbauer SIEMENS AG Hofmannstr. 51 81359 Munich, Germany HannsJuergen.Schwarzbauer@icn.siemens.de Klaus D. Gradischnig NeuStar, Inc 1120 Vermont Ave. N.W.Suite 400 Washington D.C 20005 klaus.gradischnig@neustar.com Ken Morneault Cisco Systems Inc. 13615 Dulles Technology Drive Herndon, VA, USA 20171 EMail: Malleswar Kalla Telcordia Technologies MCC 1J211R 445 South Street Morristown, NJ, USA 07960 Email: kalla@research.telcordia.com Normand Glaude Performance Technologies 150 Metcalf Sreet, Suite 1300 Ottawa, Ontario, Canada K2P 1P1 EMail: nglaude@microlegend.com Brian Bidulock OpenSS7 Corporation c/o #424, 4701 Preston Park Blvd. Plano, TX, USA 75093 EMail: bidulock@openss7.org This draft expires December 2001. Sidebottom et al [Page 100] | ||||||||||||||||
Last modified: Mon, 26 Aug 2024 22:28:06 GMT Copyright © 2014 OpenSS7 Corporation All Rights Reserved. |